258699
72
Verklein
Vergroot
Pagina terug
1/81
Pagina verder
Appendix B. Hard disks and BIOS setup
The appendices below provide you with extra information on the hard disk
organization, how information is stored on disks, how disks should be installed in
the computer and plugged into the motherboard, configuring disks with BIOS,
partitions and file systems, and how operating systems interact with disks.
B.1 Installing hard disks in computers
B.1.1 Installing a hard disk, general scheme
To install a new IDE hard disk, you should do the following (we will assume you
have powered OFF your PC before you start!):
1. Configure the new hard disk as
slave by properly installing jumpers on the
board of its controller. Disk drives generally have a picture on the drive that
shows the correct jumper settings.
2. Open your computer and insert the new hard disk into a 3.5
’’ or 5.25’’ slot with
special holders. Fasten down the disk with screws.
3. Plug the power cable into the hard disk (four-threaded: two black, yellow and
red; there is only one way you can plug in this cable).
4.
Plug the 40- or 80-thread flat data cable into sockets on the hard disk and on
the motherboard (plugging rules are described below). The disk drive will have
a designation on the connector or next to it that identifies Pin 1. The cable will
have one red wire on an end that is designated for Pin 1. Make sure that you
place the cable in the connector correctly. Many cables also are “keyed” so that
they can only go in one way.
5. Turn your computer on and enter BIOS setup by pressing the keys that are
displayed on the screen while the computer is booting.
6. Configure the installed hard disk by setting the parameters
type, cylinder, heads,
sectors and mode (or translation mode; these parameters are written on the
hard disk case) or by using the IDE autodetection BIOS utility to configure the
disk automatically.
7. Set the boot sequence to A:, C:, CD-ROM or some other, depending on where
your copy of Acronis True Image Home is located. If you have a boot diskette,
set the diskette to be first; if it is on a CD, make the boot sequence start with
CD-ROM.
8. Quit BIOS setup and save changes. Acronis True Image Home will automatically
start after reboot.
9. Use Acronis True Image Home to configure hard disks by answering the
wizard’s questions.
10. After finishing the work, turn off the computer, set the jumper on the disk to
the
master position if you want to make the disk bootable (or leave it in slave
position if the disk is installed as additional data storage).
B.1.2 Motherboard sockets, IDE cable, power cable
There are two slots on the motherboard to which the hard disks can be connected:
primary IDE and secondary IDE.
72 Copyright © Acronis, Inc., 2000-2006
72

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Acronis true image 9 1 server bundle bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Acronis true image 9 1 server bundle in de taal/talen: Engels als bijlage per email.

De handleiding is 2,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Acronis true image 9 1 server bundle

Acronis true image 9 1 server bundle Gebruiksaanwijzing - Deutsch - 140 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info