810507
43
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
41
Degree of protection IP
The cover of the operating module of the controller ensures different degrees of IP
protection, depending on the method of installation. After installation performed
according to this figure on the front of the operating module cover, the device has a
degree of protection IP20 (indicated on the rating plate). On the side of the terminals, the
cover has an IP00 degree of protection, therefore the terminals of the operating module
must be installed in such a way that access to this part of the housing is prevented. If it is
necessary to gain access to the parts with terminals, it is necessary to disconnect the power
supply, make sure that the terminals and cables are not energized, and only then remove
the cover of the operating module.
Wiring connection
The controller is designed for power supply with voltage 230V ~, 50Hz.
Properties of electrical installation:
three - core cable (with protective conductor),
carried out in accordance with valid regulations,,
Equipped with a residual current device with an operating current of IΔn≤30mA, which
protects against the possibility of electric shock and limits damage to the device,
including fire protection.
ATTENTION: Dangerous voltages can be present at the controller terminals
when the controller is switched off using the keys. Before starting installation
work, it is essential to disconnect the mains voltage and make sure that the
terminals and cables are not under dangerous voltage. Equipped with a residual
current device with an operating current of IΔn≤30mA, which protects against
the possibility of electric shock and limits damage to the equipment, including
fire protection.
The connecting cables must not touch surfaces with a temperature exceeding their
nominal operating temperature.
The terminals of each module, numbered 1-21, are intended for the connection of devices
with a mains voltage of 230V ~. Terminals 22-49 are designed for cooperation with low
voltage devices (below 12VDC).
Connecting the 230V ~ mains voltage to terminals 22-49 and the RS485
transmission connector will damage the controller and cause a risk of electric
shock!
The ends of the connecting cables, especially the power cables, must be protected by
insulated crimp terminals, as shown in the following figure:
3URWHFWLRQRIFDEOHV¶HQGVDFRUUHFWELQFRUUHFW
Feed cable must be connected to the terminals marked with an arrow .
43

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ATTACK Pellet 30 Automatic Plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ATTACK Pellet 30 Automatic Plus in de taal/talen: Engels als bijlage per email.

De handleiding is 0.97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van ATTACK Pellet 30 Automatic Plus

ATTACK Pellet 30 Automatic Plus Gebruiksaanwijzing - Deutsch - 56 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info