810499
39
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
39
4.16 MAINTENANCE OF THE HEATING SYSTEM AND THE BOILER
It is necessary to check, eventually to refill the water in the heating system at least 1x in 14 days.
If the boiler is out of order during the winter period and the water could freeze in the heating
system, then the water should be replaced with an antifreeze mixture approved by the producer
or it should be discharged out of the system. Normally should be the water discharged only in
urgent cases and for ash short time as possible. At the end of the heating season it is necessary
to clean the boiler properly and to replace the damaged parts. Twice a year it is necessary to
dismantle the fan, to clean the radial impeller and to clean the fan air chamber.
Exchange of the sealing cord of the door
Undo the worn sealing cord by the screw driver and clean the groove, where it was laid. Take the
new sealing cord and put its ends into the horizontal parts of the groove. Use your hand,
eventually a hammer to press the cord into the groove around the door.
Adjusting the hinges
After a particular period is the sealing cord in the door pressed. To ensure its tightness is
necessary to change the position of the door by screwing the door hinges. The feeding door and
the bottom door are fixed to the boiler body by two hinges that are connected to the door by
a long joint. To adjust the hinges, it is necessary to remove the joint and to turn and to screw the
joint. Fix the door and put the joint into the hinge.
Replacement of the nozzle
The nozzle is laid in the boiler body on the holder. In the bottom part is the nozzle sealed by
a boiler sealant and in the upper part there is a sealing cord around. When replacing the nozzle,
remove the sealing cord from the groove by a screw driver. Take the nozzle out and clean the
holder properly from tar and old sealant. Then treat the bottom part of the nozzle with the
fireproof sealant and put the nozzle on the clean holder with the arrow towards the rear boiler
part. There should be the same space on the both sides of the nozzle. Take the new set of the
sealing cords for the nozzle and press it lightly into the gap just around the nozzle.
Adjustment of burning in the boiler
The burning is adjusted by the primary and secondary regulation flap. Producer sets the boilers
to the optimum conditions of burning with reference to the emissions and flue gas temperature.
Only the service staff trained by producer can make the adjustment.
Warning
It is not possible to use the warranty service to set the boiler combustion, to correctly set the
door, to replace the door seal and to replace the worn nozzle because of dependence
on the installation conditions, the wear and tear of the product, the product connection on the
chimney, and the type and quality of the fuel used!
39

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ATTACK DPX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ATTACK DPX in de taal/talen: Engels als bijlage per email.

De handleiding is 11.03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van ATTACK DPX

ATTACK DPX Aanvulling / aanpassing - Deutsch - 21 pagina's

ATTACK DPX Gebruiksaanwijzing - Deutsch - 48 pagina's

ATTACK DPX Aanvulling / aanpassing - English - 21 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info