810499
15
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
15
Turn the flue gas thermostat to „0 °C“. Put one layer of the medium thick wood logs (of approx.
50 mm length)through the upper door on a fire proof nozzle. Then, make the layer of thin wood
with the gap of 2 4 cm and lay splinters or wood wool and paper on it. Continue with 2 layers
of thin dry wood and complete it with the standard firewood. Turn the exhaust fan on and after
the wood is ignited, let the feeding door open for approximately 15 mm. Use the output
regulator to set the required water temperature (80 90 °C). When the fire is strong enough
(after approximately 10 minutes), close the feeding door. Set the flue gas thermostat to the
operating temperature (white mark upwards, approximately 90° to the right from the zero
position – it depends on the flue gas temperature required to stop the boiler after the fuel burns
out).
WARNING: The pull rod of the heat up flap has to be pushed backwards to close the
heat up flap. Otherwise the fan could get damaged.
For wood gasification in the boiler it is necessary to keep the reduction layer during the
operation (the layer of wood coal on the nozzle in the feeding chamber). Therefore it is
necessary to burn dry wood of a suitable size. When the wet wood is burned, the boiler does not
work as a wood gasifying boiler, the wood consumption rises, the output is not sufficient and
service life of the boiler and of the chimney is shortened.
When there is a prescribed chimney draught, the boiler works up to 70 % of its output even
without the fan.
Electromechanical boiler regulation
The boiler is regulated by the boiler thermostat placed on a boiler panel which controls the fan
according to the adjusted output temperature of water. The required operating boiler
temperature should be set on the boiler thermostat. The flue gas thermostat placed on a panel
serves to stop the fan after the fuel burns out. Set the flue gas thermostat to „0 °C“ when heating
up. When the fire is sufficient, set it to the operating position to let the fan run and to stop it after
the fuel burns out. The optimal position of the flue gas thermostat has to be found by
experience, adequately to the fuel used, chimney draught and other conditions. The output
temperature of water is indicated on thermo-manometer. The irreversible safety thermostat is
also placed on the front panel (the STANDARD and LAMBDA version).
Refilling the fuel
When refilling the fuel, open the feeding door. The heat up flap is opened at the same time. Do
not stop the fan. Always keep the feeding chamber full when heating up. Not to let the smoke
flow into the boiler room, refill the fuel after it is burned to approximately 1/3 of the feeding
chamber. Cover the glowing coal with a wide wood log and refill the fuel normally. Do not press
the fuel on the nozzle, otherwise it could get clogged and the parameters of burning would be
worse.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ATTACK DPX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ATTACK DPX in de taal/talen: Engels als bijlage per email.

De handleiding is 11.03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van ATTACK DPX

ATTACK DPX Aanvulling / aanpassing - Deutsch - 21 pagina's

ATTACK DPX Gebruiksaanwijzing - Deutsch - 48 pagina's

ATTACK DPX Aanvulling / aanpassing - English - 21 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info