810510
47
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
46
EN
9.4 DESCRIPTION OF FUNCTION
ATTENTION: The burner is controlled on the basis of the boiler temperature sensor (in
the burner menu must be set in the advanced settings THERMOSTAT to the "Combina-
tion") or room thermostat, if is connected to the terminals TP under the electrical scheme.
It is possible to choose boiler temperature and hysteresis in burner menu. The burner will
try to achieve the set temperature and according to hysteresis the burner will be turned
on.
9.4.1 NORMAL START–UP IN STAND–BY MODE OF BURNER
When the thermostat gives instruction to the burner, the ventilator starts and the photocell con-
trols the fire. If there is no fire, then comes the instruction to blow the burner through. After-
wards, pellets start to fall into the burner within the period stated by the control system and the
ignition is activated. After the phase of fuel feeding for ignition is finished, the control system
waits for signalization of fire from the photocell. When the photocell recognizes the fire, small
amounts of pellets fall within the transition period. Duration of this depends on the output level
set on the burner. Pellet supply is gradually increased, until the necessary fuel amount for the
required output is achieved. This amount is further delivered into the burner, until the operation
thermostat gives instruction to stop.
This signal stops the pellet inlet, while ventilator continues to supply the air into the burner.
When the photocell recognizes burn–out of pellets, the blow–through of the burner begins.
According to the adjusted delay, the burner is cleaned after the fuel burns out – the grate moves
out towards the scraper and the ash with the unburned elements falls through the front wall of
the burner´s bottom into the ashpan. After the grate slides back, the burner waits for the new
signal from thermostat.
CAUTION: : The unit for the grate moving is very strong and it might cause a threat. Nev-
er put any body parts or foreign articles into the burner, while it is working.
9.4.2 BURNER START–UP, WHEN THERE IS STILL FIRE IN THE BURNER
If the photocell recognizes the fire during the beginning phase (e.g. after the short time current
shortage), the control system directly begins the transition–phase and the pellet burner contin-
ues to operate as by normal start. (see above)
9.4.3 BURNER START–UP, WHEN THE CONTROL SYSTEM DOES NOT RECOG-
NIZE THE FIRE
The normal start–up process follows, also when the control system does not receive the fire sig-
nal. The system starts shortly after repeated ignition process, which increases the ignition
amount in the combustion chamber and heating of spiral continues until the photocell does not
detect the presence of flame. These parameters are adjustable only by the trained person in ser-
vice menu. If the second trial fails, all functions are turned off and the alarm is activated. This
alarm is indicated on display.
47

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ATTACK DPX Combi Pellet bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ATTACK DPX Combi Pellet in de taal/talen: Engels als bijlage per email.

De handleiding is 8.73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info