810510
37
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
36
EN
ler´s operating mode (reaching the flue gas temperature of [
c
90]). If the temperature of [
c
90] is
not reached during the heating up, the fan is stopped and the alarm FUEL (fuel shortage) is dis-
played.
[Fb30] Duration of boiler stop by flue shortage and burn–down – the fuel amount test is ac-
tivated in the operating mode, when the flue gas temperature decreases under the parameter [
c
90] or (if the flue gas sensor is not connected) when the boiler temperature decreases under the
adjusted parameter [L 45]. If the temperature does not exceed the necessary limit during this
period, the controller displays FUEL alarm.
[Ar 0] Operation of multifunction additional output – the controller is equipped with an addi-
tional multifunctional outputs compatible with the options listed below (to control these op-
tions is necessary to use an additional module UM – 1):
[Ar 0] parameter – indicates start of the automatic boiler (e.g. gas or pellet boiler). When the
controller is started and the boiler generates heat, the automatic boiler is stopped. Operation
of the automatic boiler is blocked by the controller in the operating mode. The automatic
boiler is started by controller, when the fuel is burned down in the boiler and the FUEL alarm
is displayed.
[Ar 1] parameter – indicates that the additional multifunctional output will be used for error
messages like boiler sensor failure, overheating or fuel shortage.
[
c
240] Adjusted flue gas temperature – the controller will struggle to reach and to keep this
value. The flue gas temperature sensor is turned off, if this parameter is set to „– –“.
[
c
h5] Hysteresis of flue gas temperature – defines the difference for which must the flue gas
temperature decrease to increase the fan rotations.
[
c
t 5] Time constant of stabilization the flue gas temperature – defines the period of adjust-
ing the fan rotations during stabilization of the flue gas temperature. If the flue gas temperature
exceeds the value given by the parameter [
c
240], the controller starts to decrease the fan rota-
tions gradually, until the flue gas temperature decreases to the adjusted value. If the flue gas
temperature decreases to the value of flue gas temperature hysteresis, the controller starts to
increase the fan rotations gradually.
[
c
F10] Blower speed jump while stabilizing exhaust gas temperature – defines the change
of rotations to achieve the adjusted flue gas temperature.
[
c
90] Flue gas temperature by fuel shortage – the message „FUEL“ for fuel shortage is dis-
played after the flue gas temperature decreases under this value.
Testing the regulator outputs:
It is possible to make a check to test the correct functionality of the regulator and devices con-
nected. The correct function of fan is tested by selecting the [outΠ] on display and holding the
„OK“ button. Test of the circuit pump is done by selecting the [outP]. Select the [outu] to start
the additional output and [outr] for multifunctional additional output.
Reset of the regulator´s pruduction settings:
There is a possibility to reset the production settings of the regulator by selecting the [Prod] in
the service menu and confirming by „OK“ button. Then is the regulator set to the values given in
the Table 3.
Exit from service menu:
Select the [End] on display and press the „OK“ button to exit from service menu.
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ATTACK DPX Combi Pellet bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ATTACK DPX Combi Pellet in de taal/talen: Engels als bijlage per email.

De handleiding is 8.73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info