520584
3
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
3
Installation and Operating Instructions
Infrared radiator BY 801 S
EN
1. Important Information
Keep these instructions in a safe place and pass them on to
possible future owners.
The device must not be used in industrial areas, and must
only be used within enclosed rooms.
The device may only be installed and repaired by a qualified
electrician in accordance with the applicable safety
regulations.
Disconnect from the power supply in the event of a fault.
Do not cover the heating device with any objects - fire
hazard!
Observe the minimum clearances.
Caution! The outer surfaces of the device are
hot during operation.
Do not leave the heating device unattended when in use.
This applies particularly with small children or persons with
impaired health who are not able to vacate the radiation
area or the room when the temperature reaches an
excessive level.
Children or persons who are not capable of operating the
device safely must not operate the heating device. Ensure
that children do not play with the device.
Do not operate the heating device in rooms where highly
inflammable substances are used (e.g. solvents, etc.).
2. Minimum Clearances, Notes on Installation
The minimum clearances must be observed.
A minimum clearance of 1 metre must be observed within
the radiation area.
Inflammable objects must not be placed in the radiation area
of the heating device.
The heating device must be aligned horizontally and
installed on a vertical wall (see illustration).
The device must be installed at a minimum height of 1.8
metres.
It is not permissible to install the device vertically or on the
ceiling.
The protection areas defined in VDE 0100 Part 701 must be
observed during installation.
Do not place the device directly below a wall socket.
Install the device in such a manner that it cannot be touched
by a person in the bathtub or under the shower.
The device plug must be accessible after installation.
Installation on wooden walls is permissble.
Due to the heat radiation of the device, the surface on which
the device is installed can darken in colour.
Remove transport fastening
Only plug in the heater after installation.
- Loosen the front grill screws (A) and remove the front grill.
- Remove the transport fastenings (B) from the heating
element.
- Re-attach the front grill.
Wall Mounting
To achieve the stipulated minimum installation height of
1.8 metres, the mounting holes for the wall holder must be
drilled at a height of 1.9 metres.
- Loosen the screw on the cover of the wall holder and
remove the cover.
- Fold the radiator forward.
- Mark and drill the mounting holes on a vertical wall and
insert dowels.
- Insert spacers with screws into the openings of the wall
holder and screw the device into place.
3. Electrical Connection
Do not lay the connection cable in the radiation area and on hot
surfaces of the heating device. The voltage specified on the
type plate must match the mains voltage.
Plug in the heater. The device plug must always be accessible.
If the power line of this device is damaged, it must be replaced
by the manufacturer or after-sales service, or else by a similarly
qualified person, in order to prevent risks.
A
A
B
B
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AKO BY 801 S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AKO BY 801 S in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 2,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info