483364
24
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
English
24
Assembly instructions
The device must be completely assembled before use!
While reading the text it is advisable to refer to the
„Overview of the Components“ (Illustration A).
1. Position the rear protection grid (6) in place in ac-
cordance with the recesses.
ޥ NOTE:
Please note that the borehole for the fastening
screw (3) faces downwards.
2. Turn the attachment ring (5) for the rear protection
grid (6) slightly in a clockwise direction.
3. Attach the propeller (4) to the motor shaft (7) and
press it  rmly into place.
4. Insert the front protective grille (1).
ޥ NOTE:
Ensure that the holes for the attachment screw in
the front and rear protective grille are aligned one
above the other.
5. Tighten the protective grille with the attachment
screw (3) supplied.
6. Close the attachment hooks (2).
Position
The ideal position is a non-slip,  at surface.
Wall Installation
You can also install the fan on the wall. Please remember
that there must be an electric socket close by.
Setting up the Fan (Illustration B)
1. Release the wing screw (12) on the joint.
2. Remove the stopper (11) by loosening the screw.
3. Turn the motor through 90°.
4. Turn the wing screw until it is hand-tight.
Attachment to the Wall (Illustration. C)
On the underside of the switch housing there are two
indentations. The distance between these indentations
is 36 mm.
Drill two horizontal holes at this distance. .
CAUTION:
Please ensure beforehand that you will not be
damaging any pipes or electric wires concealed in
the wall!
Insert rawlplugs into the holes.
Please use two screws of size 4 x 25 mm. Allow the
screws to protrude 10 – 12 mm out of the wall.
Suspend the switch housing by the screws. Check
that it is  rmly held in place.
Putting into Service
Electrical Connection
1. Before inserting the plug into the socket. Make sure
that the mains voltage to be used matches that of
the device. You can  nd this information on the
nameplate.
2. Connect the device to a duly installed 230V/50Hz
protective contact socket.
Use
Basic Settings
Set the blower inclination angle before starting the
device.
In order to do this, release the wing screw (12) and
move the fan to the desired position.
Retighten the wing screw by hand.
ޥ NOTE:
The stopper prevents the fan from falling over.
Operation
Use the pushbutton switches on the front to select the
speed:
1 = slow, 2 = fast.
Shift to „0“ to switch o the device.
Blower Direction/Oscillation
You can choose from the two following options:
1. Turn the device carefully with by hand by holding the
fan on the sides and turning it either to the left or to
the right until the limit stop
.
CAUTION: do not exceed this limit.
The device must have been switched o before. The
setting knob must be pulled out.
2. Select the automatic swinging direction by pressing
in the knob. The device swings automatically within
a range of 90°. This function is active only when the
fan is on. To deactivate the function pull out the set-
ting knob.
Cleaning
WARNING:
Always remove the mains plug before cleaning the
device.
If you need to remove the safety guard: Always
switch the device o and remove the mains plug.
Under no circumstances should you immerse the
device in water for cleaning purposes. Otherwise
this might result in an electric shock or  re.
05-VL 5528 AEG neu.indd 2405-VL 5528 AEG neu.indd 24 02.12.2008 9:53:50 Uhr02.12.2008 9:53:50 Uhr
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AEG VL 5528 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AEG VL 5528 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 1,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info