463221
10
Verklein
Vergroot
Pagina terug
1/37
Pagina verder
18 19
SMT 355 (110 V) SMT 355 (220-240 V)
.......................1800 W .........................2300 W
.......................3800 min
-1
.....................3800 min
-1
.........................355 mm ........................355 mm
........................25,4 mm .......................25,4 mm
........................16,5 kg ..........................16,5 kg
...........................89 dB (A) ......................89 dB (A)
.........................102 dB (A) ....................102 dB (A)
.......................< 2,5 m/s
2
......................< 2,5 m/s
2
..........................1,5 m/s
2
.........................1,5 m/s
2
the cut-off wheel from the workpiece while the wheel is in
motion otherwise kickback may occur. Investigate and take
corrective action to eliminate the cause of wheel binding.
Do not restart the cutting operation in the workpiece. Let the
wheel reach full speed and carefully reenter the cut. The
wheel may bind, walk up or kickback if the power tool is
restarted in the workpiece.
The workpiece must be xed.
Regularly clean the power tool’s air vents. The motor’s fan
will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
Ensure that the machine is always stable and secure (e.g.
xed to a bench)
Long workpieces must be adequately supported.
SPECIFIED CONDITIONS OF USE
The Cutting-off Grinder is to be used for cutting metal
sections, metal pipes and metal bars into lengths. The
machine is not designed for wood working.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 61029, EN 55014-1, EN 55014-2, EN
61000-3-2, EN 61000-3-3, in accordance with the
regulations 2006/42/EC, 2004/108/EC
Winnenden, 2010-05-18
Rainer Kumpf
Manager Product Development
Authorized to compile the technical le
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Always wear goggles when using the
machine.
Do not dispose of electric tools together
with household waste material! In
observance of European Directive 2002/96/
EC on waste electrical and electronic
equipment and its implementation in
accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling
facility.
ENGLISHENGLISH
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Appliances used at many different locations including open
air should be connected via a residual current device of
30 mA or less.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
Sawdust and splinters must not be removed while the
machine is running.
Never reach into the danger area of the plane when it is
running.
Always use the protective shields on the machine.
Never use the Cutting-Off Grinder to cut materials other
than those specied in the instruction manual.
The handle lock must always be engaged when transporting
the Cutting-Off Grinder.
Only use the Cutting-Off Grinder with guards in good
working order and properly maintained, and in position.
The adjusting nut must be tightened before starting to work
with the machine.
Do not use cut-off wheels which are damaged or deformed
Always use and store the cut-off wheels according to the
manufacturer‘s instructions.
Use only cut-off wheels that are recommended for your
power tool and the specic guard. Cut-off Wheels for which
the power tool was not designed cannot be adequately
guarded and are unsafe.
Do not attach a saw chain, woodcarving blade or toothed
saw blade. Such blades create frequent kickback and loss
of control.
The guard must be securely attached to the power tool and
positioned for maximum safety, so the least amount of
cut-off wheel is exposed towards the operator. The guard
helps to protect operator from broken cut-off wheel
fragments and accidental contact with cut-off wheel.
The arbour size of the cut-off wheel and the ange must
properly t the spindle of the power tool.
Check cut-off wheels before use. The cut-off wheel must be
properly mounted and turn freely. Perform a test run for at
least 30 seconds without load. Do not use damaged, out of
round or vibrating cut-off wheels.
Always use undamaged wheel anges that are of correct
size and shape for your selected cut-off wheel. Proper
wheel anges support the cutting wheel thus reducing the
possibility of wheel breakage.
When cutting metal, ying sparks are produced. Take care
that no persons are endangered. Because of the danger of
re, no combustible materials should be located in the
vicinity (spark ight zone). Do not use dust extraction.
Do not use a damaged cut-off wheel. Before each use
inspect the cut-off wheel for chips and cracks, tear or
excess wear.
After switching off, the machine will not be idle immediately.
(After-running of the cut-off wheel.) Allow the cut-off wheel
to come to a stop after switching off.
Do not “jam” the cut-off wheel or apply excessive pressure.
When cut-off wheel is binding or when interrupting a cut for
any reason, switch off the power tool and wait until the
wheel comes to a complete stop. Never attempt to remove
TECHNICAL DATA Metal Cutting-Off Grinder
Rated input .............................................................................
No-load speed ........................................................................
Cut-off wheel diameter ...........................................................
Hole diameter cut-off wheel ....................................................
Weight without cable ..............................................................
Noise Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ......................................
Sound power level (K = 3 dB(A)) ...........................................
Wear ear protectors!
Vibration Information
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
h
: ...................................................
Uncertainty K = ......................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signicantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AEG SMT 355 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AEG SMT 355 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info