473798
60
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
Protect PV.500 Operating Instructions
56 of 70 80000031354 BAL
7.2.5 Network Integration Configuration
For network integration, you will need free IP address for the COM
server, the subnet mask plus the IP address for the gateway. This
information can be obtained from your administrator if necessary.
Start the "Digi Device Discovery" tool.
The tool searches the network for Digi modules. The modules
found are displayed. If several units are found, please select
the unit to be configured using the MAC address. This can be
found on the Digi module sticker on the COM server. If no
modules are detected, check your network and and firewall
settings. Run the search again using "Refresh view".
Select the required unit. You can enter the necessary network
parameters using the right mouse button + "Configure network
settings".
Use "Save" and "Reboot" to apply the settings and complete
the installation.
Exit the "Digi Device Discovery" tool.
You can use the "ping" command to test whether the COM
server can be reached on the network.
7.2.6 Configuration of the Virtual COM Port
Communication with the COM server takes place via a virtual COM
port, which is implemented by means of a RealPort driver. In order
to do this, the RealPort driver needs to be installed and configured.
Start the RealPort driver installation process. For this purpose,
the COM server must be connected to the network and the
network parameters must be set.
The installation program searches the network for Digi
modules. The modules found are displayed along with the
configured IP address and MAC address. If several units are
found, please select the unit to be configured using the MAC
address and select "Next". The MAC address can be found on
the Digi module sticker on the COM server. If no modules are
detected, check your network and and firewall settings. Run
the search again using "Refresh view".
In the "Describe the Device" window, you can make RealPort
settings. This is where you need to select the COM port via
which the application is to communicate later. All other settings
can be left as per the factory settings.
Select "Finish" to complete the installation.
The application can communicate via the set COMx port with a
baud rate of 115.2 kB as standard. 9600 kB is also possible as an
alternative. Between these two transmission rates, the COM server
has an autobaud detection function.
60

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AEG Protect PV 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AEG Protect PV 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van AEG Protect PV 500

AEG Protect PV 500 Gebruiksaanwijzing - Deutsch - 136 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info