473798
52
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
Protect PV.500 Operating Instructions
48 of 70 80000031354 BAL
Pin number Signal Description
3 B High data
8 A Low data
Housing INV housing potential
Please use a shielded fieldbus cable as the line,
e.g. 2 x 0.22 twisted pair Lapp "UNITRONIC-BUS LD".
Please connect the RS485 bus line via the bus interface connector
supplied. In an RS485 network, the ends of the bus must always
be terminated. If necessary, insert the 120 Ohm resistor supplied
between connections A and B.
Shield connection of the RS485 bus line:
Shielding is a means of weakening (attenuating) magnetic,
electrical or electromagnetic interference fields.
Interference currents on line shields are dissipated to earth by
means of a shield busbar that has a conductive connection to the
housing. A low-impedance connection to the PE conductor is
especially important to prevent these interference currents from
themselves becoming a source of interference.
If possible, only use lines with a braided shield. The shield
coverage should be at least 80%. Avoid using lines with a foil
shield because tensile and compressive stresses applied when
fastening the line can easily damage the foil, resulting in a
reduction in the shielding effect.
Please bear the following points in mind when handling the shield:
Use cable clips or shield terminal blocks made of metal to
secure the braided shield. The clips must surround the shield
and make good contact with it over a large area.
Route the shield on a shield busbar directly from where the line
enters the cabinet. Run the shield right up to the assembly;
however, ensure that it does not make contact there!
When used in PV applications, the shield of the RS485 bus line
should only be earthed on one side so that no equalising or
interference currents can flow through the shielding. However, if
several bus stations are present, you must make sure that the
shield is never interrupted.
Please always attach the shield of the RS485 bus line to earth on
the quiescent side, i.e. only one side of the shield is attached to
earth on the master or data logger side.
In the PV inverter, the shield must not be connected to the housing
in any way.
Insert the RS485 bus cable into the equipment until it reaches the
MultiCom interface, shorten it accordingly and attach both wires to
terminals A and B.
52

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AEG Protect PV 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AEG Protect PV 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van AEG Protect PV 500

AEG Protect PV 500 Gebruiksaanwijzing - Deutsch - 136 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info