473798
39
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
Protect PV.500 Operating Instructions
80000031354 BAL 35 of 70
Maintenance mode:
Maintenance mode can be triggered either via a command or by
means of remote signalling. Active earthing switches off
immediately when maintenance mode is activated. However, the
digital and analogue signals from the isometer continue to be
ignored. Active earthing is switched on again the next time a
switch is made to the "Operation" status. However, the unit
remains in maintenance mode for at least a certain time; i.e. even
if the unit is switched over to the "Operation" status, maintenance
mode is not terminated until this time has elapsed.
Starting the insulation test manually:
The insulation test can be started manually for maintenance work.
Active earthing is switched off when the insulation test is started
and the test actually commences once a delay has elapsed. When
the test period has elapsed the insulation test finishes and the
active earthing is switched on again.
The insulation test can only be started manually if an insulation
test is not already running at the time.
5.3.4 Insulation Monitoring in Compain Operation
In compain operation (see chapter 5.5), both inverters are fitted
with the isometer.
Insulation measurement in single operation
In single operation, the two inverters behave like two individual
units. Insulation measurement is active in both inverters.
Insulation measurement in linked operation
In linked operation, the inverters are connected on the DC voltage
side. If both inverter isometers were to be active in this operating
mode, this would distort the measurement of the insulation
resistance. Therefore, in linked operation, the isometer of the
inactive inverter is switched off and its sensors are disconnected
from the DC voltage. Now only one isometer is active and the
measurement of the insulation resistance is correct.
5.3.5 Insulation Monitoring Parameters
All parameters are only relevant for operation with thin-film solar
cells.
Insulation test time:
The analogue and digital signals from the isometer are evaluated
during this time.
Delay for insulation test following shutdown of K21 (earthing
of PV cells):
Once the earthing has been disconnected, this time must elapse
before insulation measurement can start.
Delay for shutdown of K21 in night operation:
Once sequence control has switched to the "Night" status, this
time must elapse before earthing is removed with contactor K21.
Minimum time in maintenance mode:
If maintenance mode has been activated, the earthing is
disconnected and remains so for at least this time.
39

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AEG Protect PV 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AEG Protect PV 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van AEG Protect PV 500

AEG Protect PV 500 Gebruiksaanwijzing - Deutsch - 136 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info