473798
31
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
Protect PV.500 Operating Instructions
80000031354 BAL 27 of 70
In this status, no power is fed into the mains.
Possible change of status:
If the DC voltage rises above a certain value for a certain time and
the mains voltage and mains frequency are within a certain range,
the unit switches to the "Operation" status. An attempt to start up is
made which involves switching on the inverter stack. If the DC
voltage collapses too dramatically during this start-up attempt, the
inverter stack is switched off again and there is a delay before
attempting to start up again. The equipment will not switch to the
"Operation" status until any dip in the DC voltage that occurs
during a start-up attempt is within acceptable limits.
If the DC voltage falls below a certain value for a certain time, the
equipment switches to the "Night" status.
If a deactivating or self-acknowledging fault is triggered, the
equipment switches to the "Fault" status.
The status can be switched from "Waiting for feed conditions" to
"OFF" using the "Off" control command.
5.1.3 The "Operation" Status
The equipment has met all conditions for operation and no
deactivating or self-acknowledging faults are present.
The monitoring parameters values are checked regularly.
In this status, power is fed into the mains and the inverter output
contactor K7 is closed.
Possible change of status:
If the generated power falls below a certain value for a certain
time, the operating conditions are no longer met. The equipment
then switches to the "Waiting" status.
If a deactivating or self-acknowledging fault is triggered, the
equipment switches to the "Fault" status.
The status can be switched from "Operation" to "OFF" using the
"Off" control command.
5.1.4 The "Waiting" Status
If the power fed in falls below a certain value when the equipment
is in "Operation", it switches to the "Waiting" status. Although the
incoming power is low, the DC voltage of the PV cell could still be
high enough and even stable enough to meet the feed conditions
in the "Waiting for feed conditions" status. So that the inverter does
not switch back on again immediately, thereby subjecting the
inverter output contactor K7 to unnecessary strain due to frequent
switching, after the "Operation" status the unit initially switches to
the "Waiting" status. It remains in this status for a certain time, only
switching to the "Waiting for feed conditions" status once this time
has elapsed.
The monitoring parameters values are checked regularly.
Possible change of status:
Once the delay has elapsed, the unit switches to the "Waiting for
feed conditions" status.
If a deactivating or self-acknowledging fault is triggered, the
equipment switches to the "Fault" status.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AEG Protect PV 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AEG Protect PV 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van AEG Protect PV 500

AEG Protect PV 500 Gebruiksaanwijzing - Deutsch - 136 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info