648392
7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
7
© 2012 OJ Electronics A/S - ® OJ ist eine eingetragene Marke der OJ Electronics A/S
Operation
EM 50-2 is equipped with an easily operated encoder button (turn
and press) and a display which describes the current situation. The
display is backlit and is illuminated by pressing the encoder button
(OK). The illumination is automatically switched o after 30 seconds.
Press the encoder button and the main menu will be shown on the
display.
Turn the button to scroll through the options. Not all the options are
shown on the display at once, but they can be accessed by turning
the encoder button.
Press OK to select a highlighted option.
ZONE 1 OFF
ZONE 2 OFF
SENSOR 1 ##.#°C
SENSOR 2 ##.#°C
MOIST 1 NO
MOIST 2 NO
OUT. TEMP ##.#°C
ALARM NO
SHOW INFO
SETUP
RESTART
EXIT
Main menu
Display texts
ZONE 1 OFF
Heating zone 1 active (ON) or inactive (OFF)
ZONE 2 OFF
Heating zone 2 active (ON) or inactive (OFF)
SENSOR 1 ##.#°C
Sensor 1 (heated sensor) core temperature.
Applies only when GROUND SENSOR sensor is
connected. NOTE: Not ambient temperature!
SENSOR 2 ##.#°C
Sensor 2 (heated sensor) core temperature.
Applies only when GROUND SENSOR sensor is
connected. NOTE: Not ambient temperature!
MOIST 1 NO
Sensor 1 moisture status. YES / NO / Blank.
Blank will be shown if temperature is above Set
Temp or the system is in Afterrun mode.
MOIST 2 NO
Sensor 2 moisture status. YES / NO / Blank.
Blank will be shown if temperature is above Set
Temp or the system is in Afterrun mode.
OUT TEMP ##.#°C
Ambient outdoor temperature. Applies only
when ETF sensor is connected.
ALARM NO
Fault message, fault type will be displayed. Red
LED on front of unit will flash.
SHOW INFO
Application info
APP: E. 1-ZONE
Application type: electric heating
SW VERSION 1.10
Software version
SENSOR 1 GRND
Sensor type, sensor 1
SENSOR 2 OFF
Sensor type, sensor 2
SENSOR ATF OFF
ATF 5 sensor connected
EXIT
Return to main menu
Settings
Please note that incorrect sensor setup may lead to poor or lacking
ice and snow melting.
Press OK and a submenu will be shown on the display.
Select the parameter to be set and press OK.
SETUP
FORCE HEAT OFF
Manual start of forced heat. Press OK and select
ON to start Forced heat.
EM 50-2 controller will heat in the pre-pro-
grammed afterrun time, see AFTERRUN 1and 2.
SELECT SCALE C
Whether temperature is to be displayed in Cel-
sius (C) or Fahrenheit (F) can be selected here.
Select the required scale and press OK. Press
OK to return to the SETUP menu.
SET TEMP 1 3.0C
Set temperature for Zone 1: The temperature
at which the ice and snow melting system will
become active can be set here. The temperature
setting can be adjusted from +50 / -20°C
(122 / -4°F). Set the required temperature and
press OK.
SET TEMP 2 3.0C
Set temperature for Zone 2: The temperature
at which the ice and snow melting system will
become active can be set here. The temperature
setting can be adjusted from +50 / -20°C
(122 / -4°F). Set the required temperature and
press OK.
OFF TEMP 1 OFF
he lowest operating temperature for Zone 1 can
be set here. Below this tempera ture, the system
will enter standby mode. The adjustment range
goes down to -20°C/OFF (-3.9°F/OFF). OFF = no
limit. To change the minimum cut-o tempera-
ture, press OK, turn the encoder button to the
desired value and confirm with OK.
OFF TEMP 2 OFF
The lowest operating temperature for Zone 2 can
be set here. The adjustment range goes down
to -20°C/OFF (-3.9°F/OFF). OFF = no limit. To
change the minimum cut-o temperature, press
OK, turn the encoder button to the desired value
and confirm with OK.
AFTERRUN 1 2:00
Afterrun time Zone 1 : An afterheat duration of
between 0 and 18 hours can be set here. The
system will continue to provide heat for the
specified time after the moisture/temperature
signal has been eliminated by a heating cycle.
Use the encoder button to set the required after-
run time and press OK.
AFTERRUN 2 2:00
Afterrun time Zone 2 : An afterheat duration of
between 0 and 18 hours can be set here. Use
the encoder button to set the required afterrun
time and press OK.
OFFSET T1 0.0C
Zone 1 temperature can be calibrated here. With
EF 50-25 H sensor, the temperature shown on
the EM 50-2 display is always the core tempera-
ture of the sensor. For calibration, please see
page 13.
EM 50-2 English
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AEG EM 50-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AEG EM 50-2 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van AEG EM 50-2

AEG EM 50-2 Installatiehandleiding - Deutsch, English - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info