660209
15
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
15
Programming Pads
Oven is shipped from the factory for single pad programming. To change
the oven default to allow double pad programming, see User Options.
To change the amount of time or the power level for a preset pad:
1. Open oven door.
READY displays.
• If door is closed or RESET pad is pressed before programming
is complete, changes are discarded and microwave exits
programming mode.
2. Press and hold pad 1 for approximately 5 seconds.
• This begins programming mode.
• Microwave will beep and P:0 displays. Oven is in
programming mode.
3. Press pad to be reprogrammed.
• Press two pads if reprogramming a double pad program.
COOK LEVEL and cooking time display.
• A number displays with COOK LEVEL if it is less than full power.
4. Enter cooking time by using the number pads.
5. Press POWER LEVEL pad to change power level if desired.
• Use the number pads to change power level to a lower
power setting.
6. Press START pad to set new programming to the pad.
• If START is not pressed, changes will not be saved.
P:0 displays
7. Press STOP/RESET pad or close oven door to exit
programming mode.
Programming Multiple Stages
Stage cooking allows consecutive cooking cycles without interruption.
Up to four different cooking cycles can be programmed into a memory
pad. To use stage cooking:
1. Follow steps 1 through 5 above.
6. Press TIME ENTRY pad.
• Display briey shows the pad number that is being
programmed and the stage number to the upper right.
Display changes to cook time and power level for the next stage.
7. Enter cook time and power level as in steps 4 and 5.
To enter another cooking stage for that pad, press TIME ENTRY
pad again.
• Up to four different stages can be programmed.
8. Press START pad to set new programming changes to the pad.
X2 Programming
This feature allows a preset
percentage of original cook
time, called a cooking factor, to be
added to a cook sequence.
To change the cooking factor:
1. Open oven door.
2. Press and hold pad 1 for
approximately 5 seconds.
3. Press pad to be reprogrammed.
4. Press the X2 pad.
5. Press a numbered pad to
change the cooking factor.
• Pad 5 would change the
cooking factor to 50%.
• Pad 3 would change the
cooking factor to 30%.
6. Press START pad to save changes.
Programming
STYLE 2
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ACP MDC182 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ACP MDC182 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van ACP MDC182

ACP MDC182 Gebruiksaanwijzing - Deutsch - 19 pagina's

ACP MDC182 Gebruiksaanwijzing - Français - 19 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info