503271
100
Verklein
Vergroot
Pagina terug
1/126
Pagina verder
Code and description Cause Measure
F04 (lock out error)
Three unsuccessful
ignition attempts.
No gas Open the main gas supply valve and/or
the manual gas supply valve before the
gas control valve
Check supply pressure to the gas control
valve
If necessary, restore the gas supply
Air in the gas pipes Bleed the air out of the gas pipe (see
section 7.9.2)
and measure the supply
pressure and burner pressure.
Defect in the hot surface igniter circuit Check that the hot surface igniter is
correctly connected (JP2).
Check the wiring of the hot surface
igniter.
Measure the resistance across the hot
surface igniter. This must lie between 2
and 10 Ohm (at room temperature).
Check that the hot surface igniter lights
up during ignition.
If necessary, replace the hot surface
igniter.
Defect in the ionisation circuit Check that the flame probe is correctly
connected (JP2)
Check the wiring of the flame probe
Measure the ionisation current. This must
be a minimum of 1.5 microA.
If necessary, replace the wiring.
Supply voltage too low Check the supply voltage, this must be 230
VAC(-15%, +10%)
F05 (lock out error)
Too many flame errors
have been signaled.
Incorrect roof or wall flue terminal.
Recirculating flue gases.
Check that the correct roof or wall flue
terminal has been installed (see section
7.7)
.
If necessary, install the correct roof or
wall flue terminal.
Check that the roof or wall flue terminal
discharges into a permitted area.
F06 (blocking error)
Short circuit between
flame probe and earth
Damaged cable in contact with metal
surface or bent flame probe.
Check the wiring and the flame probe.
Replace the wiring and/or flame probe if
necessary.
Ceramic part of the flame probe is
broken/cracked.
Check whether the ceramic part of the
flame probe is still intact, in the vicinity
of the air distribution plate of the burner.
If not the flame probe must be replaced.
F07 (lock out error)
A flame has been detected
after the gas control valve
was closed.
Defective gas control valves Check whether there is still burner
pressure present, after the gas control
valves have closed.
Check whether a flame is still present,
after the gas control valves have closed.
If this is the case, the gas control valve
must be replaced.
F08 (lock out error)
Error message from safety
relay
Flame detection before the gas control
valve opened.
Reset controller.
If the error appears again, replace the
controller.
F09 (lock out error)
Water temperature
protection.
Temperature at the top of the tank
exceeds 93 ºC.
Check that the circulation pump (if
present) is working
Check the position of temperature sensor
T
1
Reset controller
100 Installation, Maintenance and Service part
100

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw A.O. Smith SGS 30 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van A.O. Smith SGS 30 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van A.O. Smith SGS 30

A.O. Smith SGS 30 Gebruiksaanwijzing en installatiehandleiding - Nederlands - 120 pagina's

A.O. Smith SGS 30 Gebruiksaanwijzing - Deutsch - 128 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info