503271
70
Verklein
Vergroot
Pagina terug
1/126
Pagina verder
7.8.4.8 Connecting Q/T sensor
Note
You can optionally add a Q/T sensor to the installation. This enables you to calculate the
energy contribution of the system. For more information or to order the Q/T sensor,
please contact your supplier.
Connect the 5V to J12-1.
Connect sensor S4 to J12-2.
Connect earth to J12-3.
Connect the "flow signal" to J12-4.
Fit the cable in the strain relief.
If you have no more connections to make:
Fit the covers over the controller.
7.9 Commissioning
To commission the water heater:
Fill the water heater (see section 7.9.1)
Check the supply pressure (see section 7.9.2)
Check the gas control valve pressure
Measure the CO
2
(see section 7.9.4)
Switch pressure measurement (see section 7.9.5)
Turn on the water heater (see section 7.9.6)
7.9.1 Filling
7.9.1.1 Filling unvented installations
Refer to the installation diagram when you fill the water heater:
Open the stop valve (11) in the hot water supply pipe.
If applicable, open the stop valves (4) of the circulation pipe (C).
Make sure that the drain valve (9) is closed.
Open the nearest hot water draw-off point (14).
Open the stop valve (4) of the cold water supply pipe (A). Cold water flows into the
water heater.
Fill the water heater until a full water jet flows from the nearest draw-off point. The
water heater is completely full.
Open all draw-off points to bleed the entire installation of air.
The water heater is now under water supply pressure.
Make sure that no water comes out of the expansion valve (15) or the T&P valve (3).
If water comes out:
Examine if the water supply pressure is greater than the specified value in the
Technical details. If necessary, install a pressure reducing valve (1).
Examine if the expansion valve in the protected cold supply set-up is installed
correctly and is not defect. If necessary, replace the expansion valve.
7.9.1.2 Filling vented installations
To fill the water heater, proceed as follows:
Open the stop valve (11) in the hot water pipe and, if present, the stop valves (4) for
the circulation pump (6).
Close the drain valve (9).
Open the nearest hot water draw-off point (14).
Open the stop valve (4) on the cold water side (A) so that cold water flows into the
water heater.
Completely fill the water heater. When a full water jet flows from the nearest draw-
off point, the water heater is full.
Bleed the entire installation of air, for example by opening all draw-off points.
n
1.
2.
3.
4.
5.
6.
-
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
6.
7.
8.
-
-
1.
2.
3.
4.
5.
6.
70 Installation, Maintenance and Service part
70

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw A.O. Smith SGS 30 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van A.O. Smith SGS 30 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van A.O. Smith SGS 30

A.O. Smith SGS 30 Gebruiksaanwijzing en installatiehandleiding - Nederlands - 120 pagina's

A.O. Smith SGS 30 Gebruiksaanwijzing - Deutsch - 128 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info