671757
16
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
16
15
2.1.3 Gas connection
The gas supply to this appliance must
be installed in accordance with BS 6891
(1988) and British Gas Publications UP1
and UP2.
Fit the 1/2” gas supply cock supplied
with this unit immediately before the
gas control. No heat or soldered joints
should be applied in the vicinity of the
gas control, as they could cause damage
to the control. All connections and joints
should be tested for gas soundness with
a suitable leak detector (do not use a
naked ame).
N.B. When operating this unit on LPG a
suitable gas supply cock should be used.
2.1.4 Flue system
The water heater should be tted with
a ue system connected to the draught
diverter. The ue pipe should rise for
at least 50 cm. vertically before the
inclusion of any bends. If a horizontal
run of ue is required this should be
kept to the minimum lenght possible and
incorporate a rise of 6 cm. per metre
of run. A split clip or ange should be
provided in the ue close to the draught
diverter for ease of servicing.
All ue materials should be corrosion
resident i.e. stainless steel or galvanised
and must include a tested and apprved
terminal to BS 5440 part 1.
If the ue passes through any
combustible marerial measures must be
taken to protect against the possibility
of re.
All ues must terminate in free air space
approx. 1,5 metres from any vertical
surface of structure i.e. chimney stacks,
roof parapets, etc. If an existing chimney
or ue is to be used this should be swept
clean and be free of debris before an
approved liner is installed and connected
to the water heater.
2.1.5 Draught diverter
The appliance has been tted with a
ue down draught safety device. The
operation of the safeguard is based
on the principle of the Thermal Reux
Safeguard (TRS).
This TRS can be recognized by the copper
coloured spiral that is tted to the lower
edge of the draught diverter. The spiral is
connected to a thermostat by means of a
capillary tube. The wiring of the thermostat
must be connected to the thermocouple
circuit.
Important
The TRS should never be put out of
operation. The reentry of ue gasses
may cause poisoning.
2.1.6 Electrical connection
All electrical connections must be carried
out in accordance with IEE regulations
by an accredited electrical installation
company. The appliance must be
connected to the mains by means of
a permanent electrical connection. A
main switch must be tted in the phase
between the permanent connection and
the water heater. The feeder cable must
have cores of at least 3 * 1.0 mm
2
The
connecting clamps for the electricity supply
are indicated by the symbol for earth Á,
N for neutral and L for live. Always check
with a voltage tester if the live and the
neutral have been connected correctly in
the electricity supply. The electricity supply
must comply with the requirements below:
Electrical Frequency Electrically
supply fused to a
minimum of
220/240 V AC 50 Hz 5A
The maximum power consumption is
25 W
See electrical diagram for more
information, appendix 1.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw A.O. Smith BTI 100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van A.O. Smith BTI 100 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info