654492
22
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
Downloaded from Projector.com
3M
Multimedia Projector MP8635 © 3M 1999
ENGLISH
20
Section 7: Troubleshooting
7.1 Symptom/Solution Table
Symptom Cause Solution
Power cannot be The Main power is not turned on. Turn the MAIN POWER switch on.
turned on. The power cord is disconnected. Insert the power cord into an AC socket.
60 seconds have not elpsed since Wait 60 seconds before turning on power.
the power was turned off.
No picture and sound The setting of the input source is not Set the correct input using the input select button of
correct. the projector or the remote control
RGB/Video/Audio wiring to projector is Connect the cable to correct input/output source.
not correct.
Sound is heard with no RGB/Video/Audio wiring to projector Connect the cable to correct input/output source.
picture is not correct.
The brightness is set fully to dark. Press the MENU button and increase BRIGHTNESS.
Picture is displayed with Audio wiring to projector is not correct. Connect the cable to correct input/output source.
no sound The volume is set to minimum. Press the VOL button and increase VOLUME
The unit is muted. Press the MUTE button.
Color is weak and tint is The color and tint have been adjusted • Adjust the color and tint correctly.
incorrect incorrectly.
Picture is dark The brightness and contrast has been Adjust the brightness and contrast correctly.
adjusted incorrectly.
The lamp needs to be replaced. Replace the lamp with a new one.
Picture is not clear Projector is out of focus. • Adjust the focus.
LAMP indicator lights Lamp will not ignite.
• Turn off power and let cool for 45 minutes, then restart.
red.
• If problem persists call your dealer.
LAMP indicator blinks Lamp door is open.
• Lamp door is closed.
red.
Lamp module is not connected correctly.
Insert lamp module and ensure that it is secured properly.
TEMP indicator lights Temperature inside projector • Do not block the ventilation holes.
red. is too hot. Clean air filter
TEMP indicator blinks Cooling fan may be obstructed by Align metal screen.
red. metal screen under foam air filter. If fan blade is still obstructed, call service.
Both LAMP indicator and Lamp operating time is greater Change the projector lamp and reset the lamp
ON indicator blink red. than 2,000 hours. operation hours to zero.
7.2 Message/Solution Table
Error Message
Displays
NO INPUT IS DETECTED.
SYNC IS OUT OF RANGE.
CHANGE THE LAMP.
AFTER REPLACING LAMP
RESET THE LAMP TIMER.
CHANGE THE LAMP.
AFTER REPLACING LAMP
RESET THE LAMP TIMER
THE POWER WILL TURN
OFF AFTER 20 HR.
CHANGE THE LAMP.
(Blinking message)
Cause
The projector is not detecting a signal.
The horizontal frequency of input signal
exceeds projector capability.
Lamp operation time is greater than
1,700 hours.
Lamp operation time is greater than
1,979 hours which leaves 20 hours of
lamp time.
Lamp operating time is greater than
2000 hours. Safety feature shuts
projector down after 10 minutes.
Solution
Check cable connections to input device. Input device
not connected to this input mode, switch to next mode.
Switch input device to compatible resolution.
See Appendix A.5
Change the projector lamp and reset the lamp
operation hours to zero.
Change the projection lamp and reset the lamp
operation hours to zero.
Change the projector lamp and reset the lamp
operation hours to zero.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw 3m MP8635 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van 3m MP8635 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van 3m MP8635

3m MP8635 Gebruiksaanwijzing - Deutsch - 21 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info