674768
27
Verklein
Vergroot
Pagina terug
1/173
Pagina verder
27
Preparation
Preparing the Battery Pack/External Power Supply
Connecting to an External Power Supply Using a Power Cable
(USA/EXP version only)
The optional power cable (E-DC-6) allows the transceiver to be connected to an external
power supply.
1 Turn off the transceiver.
2 Connect the optional external power supply
cable (E-DC-6) to an external power supply.
Remarks Connect the red/black wire or white/red
wire to the positive (+) terminal of the
external power supply and the black wire
to the negative (−) terminal.
Set the voltage of the external power
supply at 12 to 14 V.
3 Insert the plug of the external power supply
into the EXT DC IN jack of the transceiver.
Cautions
y When using the transceiver with the external power supply cable (E-DC-6) connected to an external
power supply, pay attention to the following:
The power supply voltage must be between 12 V and 14 V.
If the voltage exceeds 16 V, malfunctions and damage to the electric circuits of the transceiver may
result. Take extra care.
Connect the red/black wire or white/black wire of the external power supply cable (E-DC-6) to the
positive (+) terminal of the external power supply and the black wire to the negative (−) terminal.
Use an external power supply having sufficient current capacity (3 A or more).
If the transceiver is used with the supplied antenna connected, the transmit RF may interfere with
the external power supply, resulting in malfunction or failure. When using an external power supply,
remove the supplied antenna and connect an external antenna. Place the external power supply
sufficiently away from the transceiver to avoid RF interference.
y Use the transceiver at the minimum required transmission power level to prevent overheating.
y Do not continue transmitting for a prolonged period. The transceiver may overheat, resulting in
malfunction or a burn injury.
y To operate the transceiver for 7 hours or longer, it is recommended that the battery pack be replaced
with the optional battery case (FBA-39).
y Recharging the fully-charged battery pack repeatedly can shorten its service life. Be extremely careful
not to continually recharge the battery when operating the transceiver using an external power supply.
y While charging the battery pack, protect the transceiver from water.
y Charge the battery pack in a place where the ambient temperature is +5 °C to +35 °C (+41 °F to +95
°F).
y If the terminals or electrodes of the battery pack are dirty, the transceiver may malfunction due to poor
contact, resulting in overheating or rupture. If the terminals or electrodes get dirty, clean them using
a dry cloth or cotton swab.
Connect the external
antenna.
External power supply
External power supply
cable E-DC-6
(optional)
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT2DR bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT2DR in de taal/talen: Engels als bijlage per email.

De handleiding is 40,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info