785523
17
Verklein
Vergroot
Pagina terug
1/25
Pagina verder
7. Trouble Shooting Table
Proceed as follows for quick detection of common faults.
DC loads must be disconnected from the batteries and the AC loads must be disconnected from the inverter before the inverter
and/or battery charger is tested.
Consult your Victron Energy dealer if the fault cannot be resolved.
Problem Cause Solution
The inverter fails to operate
when switched on
The battery voltage is too high or too
low
Ensure that the battery voltage is within the
correct value.
The inverter fails to operate Processor in no function-mode Disconnect mains voltage. Switch front switch
off, wait 4 seconds.
Switch front switch on.
The alarm LED flashes Pre-alarm alt. 1. The DC input voltage
is low
Charge the battery or check the battery
connections.
The alarm LED flashes Pre-alarm alt. 2. The ambient
temperature is too high
Place the inverter in a cool and well-ventilated
room, or reduce the load.
The alarm LED flashes Pre-alarm alt. 3. The load on the
inverter is higher than the nominal load
Reduce the load.
The alarm LED flashes Pre-alarm alt. 4. Voltage ripple on the
DC input exceeds 1.25Vrms
Check the battery cables and terminals.
Check the battery capacity; increase if
necessary.
The alarm LED flashes
intermittantly
Pre-alarm alt. 5. Low battery voltage
and excessive load
Charge the batteries, reduce the load or install
batteries with a higher capacity. Use shorter
and/or thicker battery cables.
The alarm LED is on The inverter did cut out following a pre-
alarm
Check the table for the appropriate course of
action.
The charger is not
functioning
The AC input voltage or frequency is
out of range
Ensure that the input voltage is between
185Vac and 265Vac, and that the frequency
matches the setting.
The battery is not being
charged fully
Incorrect charging current Set the charging current at between 0.1 and
0.2x battery capacity.
A defective battery connection Check the battery terminals.
The absorption voltage has been set to
an incorrect value
Adjust the absorption voltage to the correct
value.
The float voltage has been set to an
incorrect value
Adjust the float voltage to the correct value.
The internal DC fuse is defective Inverter is damaged.
The battery is overcharged The absorption voltage has been set to
an incorrect value
Adjust the absorption voltage to the correct
value.
The float voltage has been set to an
incorrect value
Adjust the float voltage to the correct value.
A defective battery Replace the battery.
The battery is too small Reduce the charging current or use a battery
with a higher capacity.
The battery is too hot Connect a temperature sensor.
Battery charge current drops
to 0 when the absorption
voltage is reached
Alt. 1: Battery overtemperature (>
50°C)
Allow battery to cool down
Place battery in a cool environment
Check for shorted cells
MultiPlus 2kVA 230V
Page 15 Trouble Shooting Table
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Victron MultiPlus 12 2000 80-32 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Victron MultiPlus 12 2000 80-32 in de taal/talen: Engels als bijlage per email.

De handleiding is 1.31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info