567740
14
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
www.velodyne.com
8 - Optimum Series User’s Manual
Following are brief descriptions of the connections described in Figure 2. More detail on these connections can
be found in the next section.
(1) LOW-PASS CROSSOVER
Use this knob to select the frequency above which you wish to roll o the signal to the subwoofer. When
the knob is turned all the way to the left, the Subwoofer Direct feature is invoked and the subwoofer
plays all frequencies up to 200 Hz.
(2) VOLUME Control
This control allows you to balance the output from the subwoofer to the main speakers in your system.
This control should be set to achieve similar volume level from between both the main speakers and
subwoofer. When pressing volume up or down, set the level while watching the LED display for reference.
The upper button increases the subwoofer level and the lower button decreases it.
Note: Volume is also controllable by using the supplied remote. When defaults are restored, the default
volume setting is 30 out of 80.
(3) AUTO ON/OFF Switch
Use this switch to select between auto-on (active) and constant on (auto-on inactive) operation.
(4) LINE OUTPUT
Connect these jacks to the LINE IN amp input to use the Optimum subwoofer’s internal high pass
crossover. See below for a more detailed explanation of this crossover.
(5) LINE INPUT/LFE Input
Connect these jacks to the LINE OUT preamp output, LFE output or subwoofer output jacks of your
receiver/processor. If using the LFE output from your receiver or processor, plug the single cable into the
“L” - LFE input or for more signal, use a “Y” connector (not included) and feed the signal into both “R”
and “L” inputs.
(6) SPEAKER LEVEL INPUT Terminals
Connect these input terminals to the speaker output terminals of your amplier or receiver. If you use
this method of connection, when you go to the receiver speaker set up menu, make sure you select the
large speaker option.
(7) IR Input
This is a connection that allows the utlization of a third party infrared remote sensor, such as Elan or
Xantech, or an extended cable for placement closer to your other remote controlled equipment. This
keeps you from awkward control angles using the infrared remote control.
(8) 12v Trigger
When this 2-conductor mini jack is connected, the amplier remains in power-o mode until the trigger
is applied. The correct trigger is +12V on the tip of the connector relative to the grounded sleeve.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Velodyne Optimum-12 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Velodyne Optimum-12 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Velodyne Optimum-12

Velodyne Optimum-12 Aanvulling / aanpassing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info