Handleiding Uniprodo Uni Roll 03 (pagina 4 van 19) (Duits, Engels, Frans, Italiaans, Spaans, Pools, Noors)

778962

Verklein

Vergroot

Pagina terug

1/19

Pagina verder

Parameter description Parameter value

Product name Rollator

Model UNI_ROLL

_01 DF

UNI_ROLL

_02 DF

Maximum load [kg] 136

Wheel diameter [”] 8

Width [cm] 67

Length [cm] 68

Height [cm] 94

Height adjustment [cm] 81.5 – 94

Seat dimensions [cm] 25x47

Seat height [cm] 54

Weight [kg] 7.74

TECHNICAL DATA

Read instructions before use.

1. USAGE SAFETY

ATTENTION! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in serious injury or even

death.

a) Follow the instructions to assemble the product.

b) If in doubt whether the product works

correctly or if it is damaged, contact the

manufacturer’s customer service.

c) Product repairs must only be carried out by the

manufacturer’s maintenance technicians. Do not

attempt to repair it yourself!

d) Both handles must be locked at the same height.

e) Before each use make sure the brakes are

working properly.

f) Before each use make sure that the product is in

good technical condition.

d) Do not exceed the maximum load specied in the

specications table.

h) Do not overload the shopping bag. It is designed

to carry light objects.

i) Do not use the product if any of its wheels is not

moving freely or if you feel that the user may tip

over with the product.

j) Do not use a damaged product.

k) Do not alter any product parts or accessories.

l) Check the technical condition of the product every

day.

2. USE GUIDELINES

The product is intended only to help people walk. The

product must only be used on at, hard surfaces. Do

not use the product on uneven and marshy terrain or

on surfaces with holes.

The product falls outside the scope of MDD 93/42/

EEC directive concerning medical devices.

The user is liable for any damage resulting from

nonintended use of the device.

2.1. PRODUCT DESCRIPTION

ACHTUNG! Product drawings referenced to by

individual numbers in the description can be found

on page 30.

Fig. 1. Models UNI_ROLL_01 DF and UNI_ROLL_02 DF

Fig, 2. Model UNI_ROLL_03 2in1

Fig. 3. Model UNI_ROLL_04 F

1. Handle

2. Brake lever

3. Handle frame with height adjustment

4. Height adjustment button

5. Walking stick holder

6. Rear wheel

7. Front wheel

8. Shopping bag

9. Seat

10. Seatback

11. Rear wheels folding mechanism

12. Front wheels folding mechanism

13. Footrest

14. Front wheel detach button

Parameter description Parameter value

Product name Rollator 2

in 1

Rollator

Model UNI_

ROLL_03

2in1

UNI_

ROLL_04 F

Maximum load [kg] 120 136

Wheel diameter [”] 8

Width [cm] 63 65

Length [cm] 98 74

Height [cm] 98

Height adjustment [cm] 85.5 – 98 88 – 98

Seat dimensions [cm] 31x43.5 25x46

Seat height [cm] 57.5 60

Weight [kg] 9.21 7.175

Whenever „device“ or „product“ are used in the

warnings and instructions, it shall mean < Rollator/

Rollator 2 in 1 >.

USER MANUAL

PLEASE NOTE! Drawings in this manual are for

illustration purposes only and in some details it

may dier from the actual machine.

The original operation manual is in German. Other

language versions are translations from German.

2.2. PREPARING FOR USE

Assembly:

All drawings concerning the assembly can be found at

the end of the user manual, starting on page 31-32.

Carefully remove the product from the packaging and

check for damage.

Models UNI_ROLL_01 DF and UNI_ROLL_02 DF

1. Release the clip and remove the knobs of the rear

wheels folding mechanism (Fig. 4).

2. Turn the rear wheels frame down (Fig. 5).

3. Insert and tighten the knobs of the rear wheels

folding mechanism. Make sure all wheels are

properly set.

4. Remove knobs of the front wheels folding

mechanism.

5. Turn the front wheels frame forwards the product

front (Fig. 6).

6. Insert and rmly tighten the knobs of the front

wheels folding mechanism. Make sure all wheels

are properly set.

7. Slide out the handles.

8. Move the frame to the sides until the cross-bar

interlock mechanism locks automatically. Check

that the seat is locked by pressing on both the

edges of the seat (Fig. 7).

IMPORTANT – Make sure that the cross-bar interlock

mechanism is securely locked and the knobs of the

rear and front wheels folding mechanisms are rmly

tightened.

FOLDING (models UNI_ROLL_01 DF and UNI_ROLL_02 DF)

Remove the accessories and, if necessary, lower the

handle. Pull the belt of the cross-bar safety locking

mechanism to release the cross-bar lock. Fold the

frame as shown in Figure 8. Pull the handles to each

other. Unscrew the knobs of the front and rear wheels

folding mechanisms. Rotate the rear wheels toward the

handles, screw in the knobs of the folding mechanism

and secure the clip-on rear legs.

Models UNI_ROLL_03 2in1 and UNI_ROLL_04 F

1. Install the front wheel in its seat on the front-side

of the frame.

• UNI_ROLL_03 2in1 only:

Pass screws through holes in the product frame,

fasten and tighten the star-knob. Repeat step 1 to

install the second front wheel (Fig. 14).

• UNI_ROLL_04 F only:

When the wheel is safely installed, you will see

coloured protrusions that will lock the wheel.

Repeat step 1 to install the second front wheel.

(see Fig. 21).

2. Install the rear wheel in its seat at the back of

the frame by simultaneously pressing the locking

bolt. The locking bolt will t into its position when

the wheel is safely installed in place. Repeat step

2 to install the second rear wheel. (see Fig. 15)

When installing the rear wheels, make sure the

wheels are installed on the exterior side of the

frame and that the brake lever is located on the

bottom side.

3. Install the handle by pressing the locking bolt at the

bottom of the handle frame and slide it into the

socket on the main frame. Repeat the procedure

for the handle on the other side (Fig. 16).

When installing the handle make sure it is pointing

toward the rear wheels. The ergonomic curve in

the handle must be facing inward.

4. Hang the shopping bag straps on the hooks on

both sides of the seat. Using the longer straps,

hang the bag on the product frame (Fig. 17).

5. (UNI_ROLL_04 F only) Install the walking stick

holder on the holder base. The walking stick

holder base can be found near the bottom of the

left side of the frame.

6. Unfold the rollator by pressing down on both

sides of the seat frame (Fig. 7).

FOLDING (models UNI_ROLL_03 2in1 and UNI_ROLL_04 F)

Pull the seat by the belt in the middle and push both

sides of the seat frame towards each other (Fig. 8).

IMPORTANT: Before use, make sure all the locking bolts

are fully extended through connecting holes (Fig. 19).

FOOTREST ADJUSTMENT (model UNI_ROLL_03 2in1)

1. Place the footrest support socket on the

protrusion on the front of the product frame. (see

Fig. 20.a.).

2. Repeat on the other side. Shift the footrests to the

inside to lock them (see Fig. 20.b.).

3. The footrests will lock in place with a “click” sound.

(see Fig. 20.c.).

Adjusting the height of the handles

Adjust the height of the handles to the needs of the

user. Press the locking button on the main frame and

pull the handle up or down. When the handle moves,

release the buttons. The button will automatically lock

at the next possible height. Repeat the process until the

desired height is set and make sure that both handles

are locked at the same height (Fig. 9).

Fasten the bag to the hook on the seat frame. The

shopping bag can be easily detached during use (Fig. 10).

How to operate the brakes

1. To brake, gently press both brakes at the same

time (Fig. 11), which will slow down and stop the

Rollator.

2. The brakes are equipped with an option to park

the Rollator (brake lock) (Fig. 12). To activate the

brake lock, press both brakes down at the same

time. You will hear a slight “click”. The brakes are

now locked.

3. To unlock the brakes, pull the brake levers again.

You will hear a slight “click” when the park function

switches o.

Brakes adjustment

The Rollator brake system requires periodic

adjustments. To adjust the brakes, loosen the locking

nut B (Fig. 13) and then tighten/loosen the nut A. After

adjusting, tighten the nut B. If further adjustment is

required, loosen the locking screw and then, using pliers,

pull the wire about a millimetre downwards. Re-tighten

the locking screw. Brakes can be now be adjusted by

loosening the nut B and tightening/loosening the nut

A as described above.

Description of Figure 13., page 25.

A. Nut A

B. Nut B

C. Wire

D. Locking screw

Preparation for use after a long storage period

After a long period of product storage, the following

elements must be checked, and if necessary adjusted or

sent to an authorized service for repairs:

• bent or damaged frame

• cracks on frame tubing connections

EN 76 EN

14.10.2018

Uniprodo Uni Roll 03 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info