487010
11
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity.
11
Assembly page 11/36
Fax +32 2 359 95 50
cover facing the head), the top of the blades perpendicular to the skin and cut to the
desired length (7). If necessary, insist on the reluctant hair.
When you get used to your hair clipper, you will be able to make layers simply by
changing the length of the combs in function of the cutting zone. These handling asks for
a special dexterity in order to obtain a correct result.
SHORT CUTS
Always cut from the back of the neck to the crown, using the longest attachment comb.
Holding it flat against the head, slowly move the clipper up through the hair. Use the same
technique for the sides, cutting from the bottom to the upper side of the head (8).
For the front of the crown, cut the hair against the direction in which it grows. Then even it
up with the sides.
For a flat top, use a flat comb, not the attachment comb. Just cut hair on top of the head
over it. To taper hair down to the neckline, use closer cutting attachment combs. Comb
hair, check for uneven spots and outline sideburns and neckline.
The four basic areas illustrated are your "road map" to easy do-it-yourself hair cutting (8).
LEVER
This lever has two main functions:
Regulation of the cutting length because in the position short hair (lever pushed to the
front side) you can cut the length of the used combs or make outlining by pulling it to the
backside, you can make the cutting length longer (this allows middle cutting lengths
above the 4 delivered combs).
Partial cleaning of the blades when in use by to and fro motions in order to remove the
hair blocked in the blades.
MAINTENANCE
Your clipper was carefully examined before leaving our factory to ensure that the blades
were oiled and aligned.
Blades must be realigned if they have been removed for cleaning or replacement.
Therefore, as the lever is pushed to the front side in short hair position, the end of the top
blade teeth is
Approximately 1.2 mm away from bottom blade. Compare your clipper blades with the
sketch (9).
If the blade alignment is incorrect, add a few drops of oil to the blades, turn clipper on for
a few moments, turn off and unplug. Loosen screws slightly and turn the upper blade until
a correct alignment. Then tighten screws once the blades are aligned (10).
Change the blades as soon as they become blunt.
To clean the blades, use the small brush delivered with your appliance and if necessary,
remove them completely.
OIL
To maintain your clipper in peak condition, the blades should be oiled every few haircuts (12).
Do not use hair oil, grease or oil mixed with kerosene or any solvent, as the solvent will
evaporate and leave the thick oil which may slow down the blades' motion.
POWER SCREW
The power screw allows you to adjust the power. It has been adjusted before leaving the
factory; however, if the voltage in your home is low, you may need to re-adjust it. To adjust, use
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Team HCS 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Team HCS 2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info