720456
7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
7
Features
This tool includes some or all of the following features.
1. Side Handle
2. Switch
3. Electronic impact energy control dial
4. Chisel position index collar
5. Lube oil-injection inlet
6. Tool holder / sleeve
7. Service indicator
Assembly and adjustments
WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories,
before adjusting or changing set-ups or when making
repairs. Be sure the trigger switch is in the OFF position. An
accidental start-up can cause injury.
Inserting and removing SDS-Max accessories (FIG. A1)
This tool uses SDS-Max chisels (refer to the inset in FIG A1
for a cross-section of a chisel shank). We recommend to
use professional accessories only.
1. Clean and grease the chisel shank.
CAUTION: Do not apply lubricant to the
machine.
2. Insert the chisel shank into the bit holder/tool sleeve (f).
Press and turn the chisel slightly until the sleeve snaps
into position.
3. Pull on the chisel to check if it is properly locked. The
hammering function requires the chisel to be able to
move axially several centimetres when locked in the tool
holder.
4. To remove a chisel, pull back the tool holder/ sleeve (f)
and pull the chisel out of the tool holder.
WARNING: Always wear gloves when you
change accessories. The exposed metal parts
on the tool and accessory may become extremly hot during
operation.
Indexing the chisel position (FIG. D)
The chisel can be indexed and locked into 12 different
positions.
1. Insert the chisel as described above.
2. Pull forward and rotate the chisel position collar (d) in the
direction of the arrow until the chisel is in the desired
position.
Setting the electronic impact power control dial (FIG. A)
Turn the dial (c) to the desired level. The higher the number,
the greater the impact energy. With dial settings from «1»
(low) to «6» (full power) the tool is extremely versatile and
adaptable for many different applications. The required
setting is a matter of experience, for example:
When chiselling soft, brittle materials or when minimum
break-out is required, set the dial to «1» or «2» (low);
When breaking harder materials, set the dial to «6» (full
power).
Fitting the side handle (FIG. A)
The side handle (a) can be mounted on the front of the
machine to suit both right hand and left hand users.
WARNING: Always operate the machine with
the side handle properly mounted..
1. Unscrew the side handle clamp knob (g).
2. Adjust the side handle (a) to the desired angle.
3. Slide and rotate the side handle to the desired position.
4. Lock the side handle in place by tightening the clamp
knob (g).
Operation instructions for use
WARNING:
Always observe the safety instructions and applicable
regulations.
(Original instructions) ENGLISH
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STHM10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STHM10 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info