Handleiding Stanley FME790 (pagina 5 van 52) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

720659

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

ENGLISH

(Original instructions)

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Features

This tool includes some or all of the following features.

1. Roller bracket

2. Roller bracket adjusting screw

3. Leg locking handle

4. Leg locking pin

5. Fxing arm

6. Carrying handle

7. Scalable bracket

8. Locking pin

Use

Preparing the stand (Fig. A)

u Lay down the stand’s top surface on the oor with the

folded legs on top.

u Push in a leg locking pin (4) and rotate that leg until the

locking pin clicks into place.

u Repeat with the remaining three legs.

u Lift the stand.

u Check to ensure the stand is stable and all locking pins

are in position.

Assembling the roller brackets (Fig. B &C)

The roller brackets help balance the workpiece during cutting

operations.

To assemble the roller brackets:

u Screw in the locking screws (8) through the locking screw

holes at both ends of the stand, as shown in Figure B.

u Insert the roller brackets (1) into the square holes at both

ends of the stand, Figure C.

u Place and tighten the adjustment screws (2) at both ends

of the stand, Figure C.

Attaching the mitre saw with supporting arms to

stand (Fig. D, E, F & G)

Prepare supporting arms (Fig. D)

u Insert two M8x60 Bolts and washers (9) into each

supporting arm.

Warning! Turn off tool switch and disconnect power before

mounting to the stand. Unintended startup during assembly

can cause injury.

To ensure balance and stability when using the saw, all four

corners of the saw must be bolted to the mounting arms

before use. Make sure bolts do not extend above the table of

the mitre saw.

Attaching mitre saw to supporting arms (Fig. E)

The saw has four holes that line up with the slots in the

supporting arms. See Figure E.

u Place the supporting arms downward.

u Lift one side of the saw and place a supporting arm

underneath, aligning the socket head cylinder cap screws

with mitre saw mounting holes, as shown in gure E.

u Seat the mitre saw onto the supporting arm, feeding the

socket head cylinder cap screws through each mounting

hole.

u Use a plain washer and nut (10) to hold in position.

u Repeat the above 4 steps to install second bracket to the

other side of the saw.

u Make sure the brackets are parallel to each other. Use a

tool adjustable wrench to tighten each nut.

Attaching the mitre saw and bracket assembly to

stand (Fig. F & G)

u Lift the saw and bracket assembly, allowing the assembly

to tilt slightly toward your body.

u When the the bracket assembly is tilted toward you, hook

its front edge onto the front rail of the stand, see Figure F.

Warning! To avoid serious injury, before seating the rear

end of the bracket, make sure the curved front edge of the

mounting bracket are securely seated over the front rail .

Failure to do so could cause you to lose control of the saw

mounting assembly.

u Lower the bracket assembly, allowing its rear edge to fully

seat over the rear rail, Figure G.

Note: Use one hand to hold the mounting bracket assembly

until both levers are securely locked.

u Check position and adjust if necessary, to make sure the

weight of the saw is evenly balanced over the rails as

shown in Figure G.

u Ensure the saw is fully seated and locked in position, then

tighten the four nuts to hold the saw to the mounting

bracket.

Removing saw from stand

u Loosen the locking arms to unlock the saw and mounting

bracket assembly.

u Lift the saw away from the rear rail of the stand to

disengage.

u Slightly tilt the assembly toward you, lift the front part of

the assembly to disengage from the front rail of the stand,

see Figure F.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Stanley FME790 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info