70198

Siemens ER 77460 Handleiding

6
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
Please detach and keep
Instructions for the installer
Before connecting the appliance to the
supply, check that it is prepared for the type of
plate.
This appliance must be installed in a place
with the proper level of ventilation. The gases
produced during combustion must be released
to the outside.
Check the size of the hob and the size of
the opening to be made on the kitchen unit.
The panelling on the work surface in the
immediate vicinity of the hob must be made of
non-flammable material. Both stratified coatings
and the adhesive used to fix them in place
must be heat resistant. Otherwise, they may
be damaged.
Electric wiring must not come into contact
with hot areas
The mains supply cable must be fixed to
the kitchen unit to prevent it from coming into
contact with hot parts on the oven or hob.
Appliances with electric components must
be earthed.
Handle the appliance with care throughout
the entire installation process. Avoid knocking
the appliance.
This appliance shall be installed in
accordance with the regulations in force
and only used in a well ventilated location.
Read the instructions before installing or
using this appliance.
SHOULD THE RELEVANT CONDITIONS
NOT BE PROPERLY SATISFIED, THE
INSTALLER, AND NOT THE
MANUFACTURER, SHALL HELD LIABLE.
Installing the hob in the
kitchen unit
Housing measurements
1- Minimum Distances (mm). Cut a hole of
the necessary size in the work surface, Fig. 1.
If it is to be installed over an oven, you must
and check the dimensions as given in the
installation manual.
Centre the hob in the hole on the work
surface.
2- The wood fibres used in the manufacture
of kitchen work surfaces are liable to swell
when they come into contact with moisture.
You are recommended, therefore, to coat cut
edges with a special adhesive to protect them
from steam or condensed water which could
deposit beneath the work surface on the kitchen
unit.
Depending on the model purchased, the
fixtures and the watertight seal (lower edge of
the hob) may come factory-fitted. If this is the
case, do not under any circumstances remove
them. The seal keeps the entire work surface
watertight and prevents leakage.
If these parts are not factory-fitted, fix the self-
adhesive seal supplied with the appliance to
The end of the input collector on gas
hobs comes with a
1
/
2
L-tube from its factory-set position.
To use this appliance in France, it is necessary
to remove the L-tube mounted in the factory
and assemble the one supplied in the accessory
bag. Fig. 4a. Do not forget to insert the seal.
If, for some reason, the L-tube should be twisted,
it is necessary to make sure that this area is
properly sealed. Make sure that all connections
performed are free of leakage.
The manufacturer does not accept any
liability for leakage on connections performed
by the installer or if the L-tube is moved or
twisted.
Check the voltage and total power on
the characteristics plate. The appliance must
be EARTHED.
Make sure that connection has been
performed in accordance with legal regulations
in force for the country in question. Comply
fully with the conditions laid down by the local
electricity company.
In order to meet normal safety standards,
the installer must supply an all-pole circuit
breaker with a contact aperture of at least 3
mm. This is not necessary when connection is
made via a socket, so long as this is accessible
to the user.
Appliances equipped with plugs should
only be connected to sockets which are duly
earthed.
The appliance is type "Y". This means that
the input supply cable cannot be changed by
the user. Only the brand's service technicians
are qualified to replace this cable. Use the right
cable type and section.
Do not tamper inside the appliance. If
necessary, call our Service Centre.
Hobs with control knobs are supplied with
a plugged or unplugged power cable.
TYPES OF CABLE
All gas 3 x 0.5 mm
2
process, you must place the diffusers and the
tops of the burners on their corresponding
burners. Also you must place the metal grids
Changing the type of gas
supply, check that it is prepared for the type of
gas in question. Our hobs leave the factory set
for the gas type indicated on the characteristics
plate.
Depending on the regulations in force in
your country, this hob may be adapted to work
with other types of gas (see characteristics
plate). To adapt the gas type, proceed as
follows:
1 -Remove the grates, covers and burner
2 -Change the injectors using a 7-mm
socket wrench and be sure to tighten them
down properly so that they are fully air-tight.
Fig. 6.
It is not necessary to adjust the primary air
on these burners.
B ) Adjusting reduced consumption on
the burner valves.
1 - Set the valves to minimum.
2 - Remove the control knobs from the
valve shafts. Fig. 7.
4 -Adjusting the by pass screw.
be tightened down fully.
clockwise direction until the correct release of
gas is reached: when the burner is changed
from the maximum to minimum settings, the
5 - Re-assembling the anti-liquid seals. All
the water-tightness of the electricity system
against the spillage of liquids on the hob.
6 - Re-assemble the control knobs.
C) Put the label which indicates the type of
gas the appliance has been adapted to near
the characteristics plate.
.
the lower edge of the hob, Fig. 2.
3 -
flame does not go out or backfire .
accessories bag and screw them into the lower
For disassembly, unscrew the clip and
proceed in the reverse manner.
Once the hob is fitted you should turn the clip
and
Remove the clips from the attached
points designed for this purpose, Fig. 3.
tighten the screw as shown in Fig. 3a.
3-
4-
If the cooking hob is to be installed
power
dimensions according
ventilation, and check the
above an oven, check that the oven is fitted
with
to the assembly
manual.
Before connecting the appliance to the
5-In order to complete the installation
For Propane and Butane Gas: the screw must
For Natural Gas: turn the screw in an anti-
The option to locate the cooking hob in the kitchen
unit (in accordance with the regulation for gas
appliances EN 30-1-1) is Type 3.
If no oven is installed under an electrical or
mixed (gas and electric) hob, place a
separator of non-flammable material e.g.
plywood or metal at a distance of 10 mm.
from the bottom of the hob to prevent access
to the lower part of the hob.
If no oven is installed under a gas hob, it is
suggested to place a separator of non-
flammable material e.g. plywood or metal at
a distance of 10 mm. from the bottom of the
hob to prevent access to the lower part of the
hob.
In the event that a drawer is located beneath
the appliance, please make sure that the
drawer contains no heat-sensitive or easily
combustible objects, such as spray cans or
shoe polish. Use a heat-resistant utility drawer
only.
Power cable: Hob:
Do not remove the disc seal.
A ) Changing the injectors on the burners
core.
.
check that the oven is sufficiently well ventilated
”
correctly on their supporting elements. Fig. 5.
en
the
characteristics
factory set
gas in question.
(Table I).
Our hobs leave the
for the gas type indicated on
(Table II).
All installation, regulation and adaptation to
other types of gas must be carried out by an
authorised installation technician,
respecting all applicable regulations,
standards and the country's electrical and
gas supply companies' specifications.
It is recommended that you call our
Technical Assistance Service for adaptation
to other types of gas. Before you begin, turn
off the appliance's electricity and gas supply.
All installation, regulation and adaptation to
other types of gas must be carried out by an
authorised installation technician,
respecting all applicable regulations,
standards and the country's electrical and
gas supply companies' specifications.
It is recommended that you call our
Technical Assistance Service for adaptation
to other types of gas. Before you begin, turn
off the appliance's electricity and gas supply.
Fig. 4. This caters for:
(20,955 mm)
threaded L-tube,
Rigid connection.
In either of the cases, do not move or twist the
(L min. 1m - max. 3m).If this method is used,
moving parts on the housing (e.g. drawers)
Connection to a flexible metal tub
and passing the tube through spaces liable
avoid both contact between this tube and
to get blocked.
valve.
in the event of damage, change the entire
the seals must be in place in order to ensure
Never dismount the valve shaft (Fig. 9):
… 6 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens ER 77460 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens ER 77460 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks als bijlage per email.

De handleiding is 3,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Siemens ER 77460

Siemens ER 77460 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk - 97 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info