Handleiding Sencor STM 7875 (pagina 10 van 11) (Engels)

758571

Verklein

Vergroot

Pagina terug

1/11

Pagina verder

- 10 - 05/2020

USING THE SAUSAGE STUFFER ATTACHMENT

1. Make sure that the food processor is correctly assembled and that the speed

control knob A13 is set to the OFF position. Insert the power plug into apower

socket.

2. Prepare asausage casing that you will stu with ground meat and allow it to soak

in lukewarm water for approx. 10 minutes. Place the ground meat mixture on to

the hopper B2. Take the sausage casing out of the water and skewer or tie up one

end and slide the other end like asock on to the sausage stuer attachment B12.

3. Use the speed control knob A13 to set the desired speed. We recommend to

initially set the lowest speed and then increase it as required. With one hand hold

the sausage casing on the attachment B12 and use the other hand to push the

ground meat mixture with the pusher B1 through the feed tube B3. If the sausage

casing sticks to the attachment B12, it is necessary to moisten it with water again.

Attention:

Do not use fingers or other items to push the ground meat in.

Always use the pusher B1 designed for this purpose.

4. To turn o the appliance, set the speed control knob A13 to the OFF position.

5. Clean out the individual parts of the attachment after each use according to the

instructions in chapter Cleaning and maintenance.

ASSEMBLING AND DISASSEMBLING THE KEBAB MAKER

ATTACHMENT

1. Proceed in the same way as when assembling the meat grinder, only with the

dierence that instead of the grinding blade B6 and the grinding plate B8, B9 or

B10, only parts B13 aB14 are used.

2. Place the moulder B13 on to the screw shaft B5 so that the notch in the grinding

chamber B4 ts into the groove in the moulder B13. Place the kebab moulder

attachment B13 on to the conical attachment B14 and complete the entire kebab

maker assembly by screwing the screw ring B7 on to the grinding chamber B4.

Place the stainless steel hopper B2 on to the feed tube B3.

3. Attach the attachment to the food processor in the same way as described in point

4 in chapter Assembling and disassembling the meat grinder.

4. When disassembling, rst remove the hopper B2. Then press the button A1 and

remove the attachment by turning it clockwise. After removing the attachment,

put the cover A2 back in its place.

5. When disassembling the attachment into its individual parts, proceed in the

reverse sequence.

USING THE KEBAB MAKER ATTACHMENT

1. Make sure that the food processor is correctly assembled and that the speed

control knob A13 is set to the OFF position. Insert the power plug into apower

socket.

2. Place the prepared kebab meat mixture on to the hopper B2. Use the speed control

knob A13 to set the desired speed. We recommend to initially set the lowest speed

and then increase it as required. Using the pusher B1, push the mixture through

the feed tube B3. The result will be ahollow meat tube that is then cut into smaller

pieces. The kebab is atraditional meal from the Middle East made predominantly

from ground meat and whole grain wheat.

Attention:

Do not use fingers or other items to push the ground meat in.

Always use the pusher B1 designed for this purpose.

3. To turn o the appliance, set the speed control knob A13 to the OFF position.

4. Clean out the individual parts of the attachment after each use according to the

instructions in chapter Cleaning and maintenance.

ASSEMBLING AND DISASSEMBLING THE COOKIE MAKER ATTACHMENT

1. Proceed in the same way as when assembling the meat grinder, only with the

dierence that instead of the grinding blade B6 and the grinding plate B8, B9 or

B10 only parts B11,B15 and B16 are used.

2. Place the separator B11 on to the screw shaft so that the notch in the grinding

chamber B4 ts into the groove in the separator B11. Insert the cookie maker

holder B16 into the screw ring B7. Screw the screw ring B7 clockwise on to the

grinding chamber B4. Complete the assembly by inserting the cookie maker B15

into the holder B16 and attaching the hopper B2 to the feed tube B3.

3. Attach the attachment to the food processor in the same way as described in point

4 in chapter Assembling and disassembling the meat grinder.

4. When disassembling, rst remove the hopper B2. Then press the button A1 and

remove the attachment by turning it clockwise. After removing the attachment,

put the cover A2 back in its place.

5. When disassembling the attachment into its individual parts, proceed in the

reverse sequence.

USING THE COOKIE MAKER ATTACHMENT

1. Place the prepared dough on to the hopper B2. Slide the cookie maker B15 to the

left or right to set the desired cookie shape.

2. Insert the power plug into apower socket. Set the required speed using the speed

control knob A13. When starting it for the rst time, we recommend that you set

speed 3 and then increase or decrease it as required.

3. Use the pusher B1 to push the dough through the feed tube B3. The food

processor will push the dough out in the required shape that you set using the

cookie maker B15. We recommend that you place atray or your palm underneath

the pushed out dough. Then cut the formed dough into smaller pieces.

Attention:

Do not use fingers or other items to push the dough in. Always

use the pusher B1.

4. When you have nished using the food processor, turn it o by setting the speed

control knob A13 to the OFF position.

5. Clean out the attachment after each use according to the instructions in chapter

Cleaning and maintenance.

BLENDING

ASSEMBLING AND DISASSEMBLING THE BLENDER

1. On to the blending jar C4, place the outer lid C2 so that its edges copy the neck of

the jar, and push it down thoroughly along its entire perimeter. Into the hole in the

lid C2, place the inner cap C1 and push it down all the way.

2. Make sure that the food processor is turned o and disconnected from the power

socket. The multi-function head A8 must be tilted down in the horizontal position

and the whisk, beater or kneading attachments must be removed. Release and

remove the top attachment hub cover A7. Place the assembled blending jar on to

the top hub and pulling it gently turn it in the direction of the symbol all the way.

The safety mechanism will prevent the blender from starting unless it is correctly

secured to the multi-function head A8.

3. To disassemble proceed in the reverse sequence.

4. Prior to starting the appliance, check that the blade assembly C6 is correctly seated

in the cu C5. Properly tighten the cu C5 on to the mixing container C4.

USING THE BLENDER

1. The blender is intended for preparing meals and drinks such as milkshakes, creamy

soups, sauces, spreads, fresh baby foods, etc. It is not intended for juicing fruit and

vegetables, preparing potato purée, yeast dough or for whipping egg whites.

2. Assemble the blender according to the instructions in chapter Assembling and

disassembling the blender, and put the ingredients (larger pieces need to be cut

up in advance) into the blending jar C4.

Note:

The maximum capacity of the blending jar C4 is 1.5 litres. Never ll it past

the maximum mark. When processing hot liquids or liquids that expand in

volume during the blending process, it is recommended to ll the blending

jar to no more than ⅔ of its maximum capacity.

3. Make sure that the food processor is correctly assembled and that the speed

control knob A13 is set to the OFF position. Connect the power cord to apower

socket. Set the required speed using the speed control knob A13. We recommend

to rst set aslower speed to allow the ingredients to mix together. Then the speed

may be increased. The pulse level is appropriate when you wish to blend food only

very quickly. To start the pulse level, turn the speed control knob A13 to the PULSE

position and hold it in this position for amoment. As soon as you release the speed

control knob A13, it will automatically return to the OFF position.

Attention:

Hot liquids up to a temperature of 55 °C may be processed in

the blending jar. The maximum operating time of the blender is

2 minutes. Do not leave the appliance in continuous operation

for longer than indicated above. Then allow it to cool down for

30minutes.

4. While blending, you may add food or liquids to the blending jar C4 through the

hole in the lid C2 after removing the inner cap C1. Never open the outer lid C2

during operation. When processing hot liquids, the inner cap C1 must remain

closed.

5. In the event that food is sticking to the blade assembly C6 or the walls of the

blending jar C4, turn the appliance o by turning the speed control knob A13

to the OFF position and disconnect it from the power socket. Make sure that

the blade assembly C6 has stopped rotating. Carefully remove the assembled

blending jar from the multi-function head A8 by turning it in the direction of the

symbol . Take o the lid and using aplastic spatula, clean the blade assembly C6

and the inside of the blending jar C4. Put the lid back on and reattach the blender

assembly to the multi-function head A8. Plug the power cord into apower socket

and continue blending.

6. After you have nished using the appliance, set the speed control knob A13 to the

OFF position and disconnect the power cord from the power socket. Check that

the blade assembly C6 has stopped rotating and carefully take the blending jar

assembly o the multi-function head A8. Put the cover A7 back in its place and use

asoft plastic spatula to remove food from the blending jar C4.

Sencor STM 7875 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info