759462
10
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
- 10 - 11/2020
Copyright © 2020, Fast ČR, a.s.
INSERTING AND REPLACING BATTERIES IN THE REMOTE CONTROL
Push down the latch of cover C13 on the rear side of the remote control C1 to
release it and remove the cover.
Insert two type AAA (1.5 V) batteries into the remote control. When inserting the
batteries, ensure the correct polarity as shown inside the battery compartment C14.
Put the cover C13 back on and click it into place.
In the event that the batteries are flat, replace them with new ones. Do not combine
various types of batteries or new and old batteries.
The signal range of the remote control is approximately 6 m.
SETTING SYSTEM TIME ON THE REMOTE CONTROL
The system time of the vacuum cleaner is the actual time according to your time
zone. It must be correctly set if you wish to use the scheduled cleaning function.
In the stand-by mode or in the charging in the charging station mode, hold down
button C11 (CLK) until the time setting value (hours and minutes) starts flashing
on the display C2.
Using buttons C5 ( ) or C8 ( ) set the time values. Toggle between the hour and
minute numbers using buttons E6 ( ) or C7 ( ).
Confirm the set time by pressing button C11 (CLK). The appliance will beep 1x and
the set time will be saved to the memory of the remote control as the system time.
If you do not perform any changes within 10 seconds, the system time setting mode
will automatically be cancelled and the time will not be saved to memory.
DEFINING THE VACUUMING AREA USING MAGNETIC TAPE
The magnetic tape I1 serves to define the vacuuming area without you having
to close doors or place artificial obstacles in the path of the vacuum cleaner. The
vacuum cleaner will recognise the magnetic tape and will not travel over it. It will
start cleaning in another direction.
Place the magnetic tape before the place that the robotic vacuum cleaner should
not clean, for example room doorway, carpet, cables on the floor or astaircase with
rounded corners, etc.
To help the magnetic tape adhere better, you can attach it to the perimeter using
standard double-sided tape. It can also be cut into smaller pieces as required.
Additional tape can be purchased to extended the defined area.
Note:
The magnetic tape must be put down prior to every cleaning session
because the robotic vacuum cleaner does not store the boundaries in
memory.
OPERATING THE ROBOTIC VACUUM CLEANER
Note:
Before starting the vacuum cleaner, always make sure that either
the dust container A5 or the complete mop unit A6 including the
respective HEPA dust filters is inserted inside.
TURNING ON THE ROBOTIC VACUUM CLEANER
Turn on the power supply to the vacuum cleaner using the main switch A3.
Press button D1. The button'sindicator will start flashing blue. When the indicator
is permanently lit blue, the vacuum cleaner is in stand-by mode and ready for
operation.
STAND-BY MODE
The stand-by mode means that the vacuum cleaner is ready for operation. Button
D1 is backlit in blue colour.
Set the vacuum cleaner to the stand-by mode by pressing button D1 on the vacuum
cleaner or buttons C9 (ON/OFF) on the remote control either by turning on the
power supply using main switch or whenever while the vacuum cleaner is running.
SLEEP MODE
The sleep mode serves to save the battery'scapacity. The vacuum cleaner enters
sleep mode either automatically after ten minutes of inactivity or when it is unable
to dock in the charging station. The backlight on button D1 will turn off and the
vacuum cleaner will automatically switch to the sleep mode.
To wake the vacuum cleaner from the sleep mode to the stand-by mode, press
button D1 on the vacuum cleaner or the control button C9 (ON/OFF) on the remote
control.
Note:
When the vacuum cleaner is in sleep mode, it is not possible to wake it
up using the mobile phone application. In sleep mode, it reacts only to
buttons D1 or C9 (ON/OFF) on the remote control.
TURNING VOICE MESSAGES ON/OFF
If you prefer not to have the vacuum cleaner make system voice messages,
deactivate this function by simultaneously pressing buttons C3 (PLAN) and C4
(HOME) on the remote control. The vacuum cleaner will only make beeps.
If you wish to reactivate the voice messages, again simultaneously press the buttons
C3 (PLAN) and C4 (HOME).
TURNING OFF THE ROBOTIC VACUUM CLEANER
If you wish to completely turn off the vacuum cleaner, set the main switch A3 to
position 0 (off ). The backlight on button D1 will turn off and the power supply will
be shut off. When the vacuum cleaner is turned off, it will not respond to any button.
SELECTING THE ROBOTIC VACUUM CLEANER CLEANING MODE
Before starting the cleaning process, check that the entry door into your apartment
or house is closed. From the floor surfaces, remove clothing, paper, toys, power or
extension cords and other items that the vacuum cleaner could suck in or catch.
Lift curtains and drapes that reach to the floor so that the vacuum cleaner does not
catch them.
Tip:
When vacuuming in a new environment for the first time, carefully
observe the movement of the vacuum cleaner. You can thereby
recognise problematic obstacles and remove them for the next
cleaning session.
AUTOMATIC CLEANING MODE
Press button D1 or button C9 (ON/OFF) on the remote control. The vacuum cleaner
will enter the automatic cleaning mode, in which it effectively combines various
routes to achieve an optimal clean of the entire floor area. As soon as the vacuum
cleaner finishes cleaning, it will seek out the charging station and dock there to
recharge.
MAXIMUM POWER MODE
Press button C12 (MAX) on the remote control. The vacuum cleaner will enter the
cleaning mode, in which it effectively combines various routes to achieve an optimal
clean of the entire floor area. This mode is characterised by increased motor and
central rotary brush power for the purpose of achieving the most effective cleaning
process.
ALONG-THE-WALLS CLEANING MODE
Repeatedly press button C10 (MODE) on the remote control so that display C2
shows MODE1. The vacuum cleaner will enter the along-the-walls cleaning mode,
in which it moves along the perimeter of the room and the motorised side rotary
brushes sweep out the dirt along the walls, furniture corners to achieve aperfect
clean. As soon as the vacuum cleaner finishes cleaning, it will seek out the charging
station and dock there to recharge.
2×2 METRE AREA (SPOT) CLEANING MODE
Place the vacuum cleaner approximately in the middle of the area that you wish
to clean.
Repeatedly press button C10 (MODE) on the remote control so that display C2
shows MODE2. The vacuum cleaner will enter the cleaning mode in which it will
move in straight parallel lines and vacuum an area of approximately 2 × 2 metres. As
soon as the vacuum cleaner finishes cleaning this area, it will seek out the charging
station and dock there to recharge.
RANDOM DIRECTION MOVEMENT MODE
Repeatedly press button C10 (MODE) on the remote control so that display E2
shows MODE3. The vacuum cleaner will enter the random direction movement
mode and will continue cleaning in this mode until the battery is almost flat. It
will then end the cleaning process and seek out the charging station in order to
recharge itself.
INTENSIVE CLEANING MODE
Repeatedly press button C10 (MODE) on the remote control so that display E2
shows MODE4. The vacuum cleaner will enter the intensive cleaning mode, where it
will clean the same location twice. It will then end the cleaning process and seek out
the charging station in order to recharge itself.
PAUSING THE CLEANING PROCESS
Press button D1 or C9 (ON/OFF) on the remote control at any time during the
cleaning process to stop the vacuum cleaner in the place where it is cleaning.
USING THE MOP UNIT
The mop unit is used for simultaneous vacuuming and dry or wet wiping of smooth
floor surfaces. It consists of the removable dust container E1, water tank E2 and the
mop fabric E3. The water tank is equipped with an electronically-controlled water
pump that automatically doses the water on to the fabric and also stops dosing
water at the end of the cleaning process to prevent water from leaking on to the
floor or the charging station.
Attention:
Only use the mop unit intended for this type of robotic vacuum
cleaner.
Do not use the water tank E2 without the mop fabric attached.
The mop unit is not intended for cleaning carpets.
Dry wiping of floors
Dry wiping is used for removing fine dust and floor polishing.
If the mop unit is inserted inside the vacuum cleaner, press latch A7 and slide the
unit out of the vacuum cleaner.
Attach the mop fabric to the underside of the water tank using the velcro zip E4 on
the water tank and insert the unit back into the vacuum cleaner.
Start the vacuum cleaner.
Wet wiping of floors
Wet wiping is used for cleaning away minor dirt and floor polishing
If the mop unit is inserted inside the vacuum cleaner, press latch A7 and slide the
unit out of the vacuum cleaner.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sencor SRV 8250 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sencor SRV 8250 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info