Handleiding Scheppach TS2800 Primaster (pagina 28 van 48) (Duits, Engels, Frans)

782536

Verklein

Vergroot

Pagina terug

1/48

Pagina verder

28 І 48

2 Place the swinging part (D) into the guide rail. The

swinging part must slide easily.

3 Depending on the type of job, push the guide rail

(G) into the guide bolts (F) with the high (1) or low

surface (2) and tighten them rmly.

4 Set the fence rail (G) to the desired degree between

+60° and -60° and tighten the clamping handle (E).

Changing the sawblade, Fig. 19

Caution! Pull out the main plug and wear safety

gloves.

Release the wing screw of the suction hood (20) and

remove the hood.

Fig. 20

Release the 4 Phillips screws of the table insert (19)

and remove the insert.

Fig. 21

Move the saw blade to the very top and release the

bolt with the saw blade key.

Attention: Left-handed thread.

Fig. 22

Remove the saw blade ange (31) and the saw blade

(32). Then change the saw blade.

When mounting the saw blade mind the recess.

After changing the saw blade, check the setting of

the riving knife and ret the table insert (19) and the

suction hood (20).

9. Transport

The machine may only be transported with suitable

lifting devices (crane or fork lift). The connection point

for the rope (crane) is on the upper band wheel cabi-

net. Never lift from the saw bench. If the machine is to

be moved frequently within the work area, use of the

wheel assembly special accessory is recommended.

10. Working instructions

After each new adjustment it is advisable to carry out

a trial cut in order to check the set dimensions. After

switching on the saw, wait for the blade to reach its

maximum speed of rotation before commencing with

the cut.

Secure long workpieces against falling off at the end

of the cut (e.g. with a roller stand etc.)

Take extra care when starting the cut!

Never use the equipment without the suction func-

tion.

Regularly check and clean the suction channels.

Make sure, that you select a saw blade that is appro-

priate for the material you intend to cut.

Connect the power tool to a dust reception facility

when cutting wood.

Do not use saw blades made out of high-speed steel

(HSS steel).

Use the push stick or the feed lever for sliding the

wood, to guide it safely past the saw blade.

Fig. 9

Fasten the wheel assembly (16) to the rear base legs

(4 and 5) using 4 hexagon bolts M6 x 16, 4 washers

6, and 4 nuts M6.

Fig. 10

Place the machine on its feet and rmly tighten all

bolts of table, legs and braces (except those of the

wheel assembly).

Fig. 11

Firmly tighten the wheel assembly in the position

where the wheels slightly touch the ground.

Fig. 12 / 12.1

Fasten the riving knife in line with the saw blade as

described in the illustration. Slightly release the bolt

without removing it. Retighten it rmly after reset-

ting. For doing this, it is necessary to remove the saw

blade insert (19, Fig. 13).

Fig. 13

After setting the riving knife, refasten the saw blade

insert (19) with 4 countersunk bolts M6 x 16.

Fig. 14

Fasten the cover (20) to the riving knife (18) with

roundhead bolt M6 x 25, washer 6, and wing nut M6.

Fig. 15

Connect the suction hose (21) to the suction hood

(20) and the suction nozzle.

Fig. 16 / 16.1

Fasten the hooked bolt to the right-hand leg side us-

ing 2 washers 6 and 2 nuts M6. The hook serves for

storing the saw blade key and the push stick.

The 2 transport handles are attached at the left and

right leg at the front of the saw using 4 hexagon bolts

M6 x 16, 4 washers 6, and 4 nuts M6.

Assembly of the longitudinal fence, Fig.17 / 17.1

/ 17. 2

1 Mount the guide rail (A) with two hexagon bolts M6

x 16 with nuts M6 (B) to the front side of the table.

2 Mount the two clamping levers (C) to the table and

the guide rail using two lock bolts M6 x 25.

3 Place the swinging part (D) into the guide rail, set the

scale to 0°, and rmly tighten the clamping handle (E).

Attention: For longitudinal cutting, the swinging part

must always be set to 0.

4 Depending on the type of job, push the guide rail

(G) into the guide bolts (F) with the high (Fig. 18.1)

or low surface (Fig. 18.2) and tighten them rmly.

5 Set the fence rail to the desired dimension and

tighten both clamping levers (C).

Assembly of the cross-cutting gauge, Fig. 18.1 /

18.2 / 18.3

1 Mount the guide rail with two hexagon bolts M6

x 16 and two nuts M6 to the left side of the table.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Scheppach TS2800 Primaster Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info