782422
25
Verklein
Vergroot
Pagina terug
1/180
Pagina verder
25
Crown Moulding Cut
• Crownmouldingcanonlybecutatonthetableusing
this mitre saw.
• Thismitresawhasspecialmitrestopsof31.6°left
and right and a bevel stop of 33.9° for a special crown
moulding 1 i.e. 52° between the back of the moulding
and the top flat surface that fits against the ceiling; 38°
between the back of the moulding and the bottom flat
surface that fits against the wall. Refer to the following
table for this crown moulding cut.
Settings Left side Right side
Inside corner Mitre angle 30° right 30° left
Bevel angle 33,9° 33,9°
Moulding
position
Top against
fence
Bottom against
fence
Finished side Keepleftside
of cut
Keepleftside
of cut
Outside corner Mitre angle 30° left 30° left
Bevel angle 33,9° 33,9°
Moulding
position
Bottom against
fence
Top against
fence
Finished side Keeprightside
of cut
Keeprightside
of cut
Note:
• Thesespecialstopscannotbeusedwith45°crown
moulding.
• Sincemostroomsdonothaveanglesofexactly90°,
fine tuning is needed and always take a test cut to
confirm the correct angles.
Pullover Cut
WARNING:
1. Never pull the cutting head assembly and spinning blade
towards you during the cut. The blade may try to climb up on
the top of the workpiece, causing the cutting head assembly
and spinning blade to kick back.
2. Never lower the spinning saw blade down before pulling
the cutting head to the front of the saw.
• Unlockthecarriage1withthelockhandle2andallow
the cutting head assembly to move freely. (Fig. 6)
• Movethemitrehandleandcuttingheadtothedesired
mitre angle and bevel angle according to the mitre cut
and bevel cut procedures.
• Graspthe sawhandle andpull thecarriage forward
until the centre of the saw blade is over the front of
the work piece.
• Activatetheswitch,thenpressthebladeguardlock
lever to lower the cutting head down.
• Whenthesawreachesfullspeed,pushthesawhandle
down slowly, cutting through the leading edge of the
workpiece.
• Slowlymovethesawhandletowardthefence,complet-
ing the cut.
• Releasetheswitchandallowthebladetostopspinning
before allowing the cutting head to raise.
Coupe de moulures de plafond
• Lesmouluresdeplafondnepeuventêtrecoupéesqu’à
plat sur le plateau avec cette scie.
• Cette scie a des butées d’onglet spéciales à 30° à
gauche et à droite et une butée de chanfrein à 33,9°
pour une moulure spéciale de plafond 1, c’est-à-dire
à 52° entre le dos de la moulure et la surface plate
supérieure qui s’attache au plafond, et à 38° entre le
dos de la moulure et la surface plate inférieure qui
s’attache au mur. Voir le tableau suivant pour la coupe
des moulures de plafond.
Réglages Coté gauche Coté droite
Coin intérieur Angle d’onglet 30° à droite 30° à gauche
Angle de
chanfrein
33,9° 33,9°
Position de la
moulure
Dessus contre le
guide
Dessous contre
le guide
Coté fini Scier à gauche
du trait
Scier à gauche
du trait
Coin extérieur Angle d’onglet 30° left 30° left
Angle de
chanfrein
33,9° 33,9°
Position de la
moulure
Dessous contre
le guide
Dessus contre le
guide
Coté fini Scier à droite
du trait
Scier à droite
du trait
N. B.:
•Cesbutéesspécialesnepeuventêtreutiliséesqu’avec
une moulure de plafond de 45°.
•Commelescoinsdelaplupartdespiècesnefontpas
un angle exact de 90°, un certain ajustement est né-
cessaire. Toujours faire une coupe d’essai pour vérifier
les angles.
Coupe radiale
ATTENTION:
1. Ne jamais tirer vers soi la tête de coupe avec sa lame
en rotation pendant la coupe. La lame risque de chercher à
grimper sur la pièce à couper, provoquant le rebond de la
tête de coupe et de la lame.
2. Ne jamais abaisser la lame en mouvement avant d’avoir
tiré la tête de coupe vers l’avant de la scie.
• Débloquerlechariot1àl’aidedelamanettedeblo-
cage 2, pour que la tête de coupe puisse se déplacer
facilement (Fig. 6).
• Mettrelamanetted’ongletetlatêtedecoupeàl’angle
d’onglet et à l’angle de chanfrein voulus (voir le mode
d’emploi pour les coupes d’onglet et de chanfrein).
• Saisirlapoignéedelascieettirerlechariotversl’avant
jusqu’à ce que le centre de la lame soit au-dessus de
la partie avant de la pièce à couper.
• Mettrelascieenmarchepuisabaisserlelevierdeblo-
cage du protège-lame pour abaisser la tête de coupe.
• Quandlascieatteintsonpleinrégime,appuyerlen-
tement sur la poignée de la scie pour commencer à
couper le bord d’attaque de la pièce.
• Déplacerlentementlapoignéedelascieversleguide
pour terminer la coupe.
• Relâcherlagachetteetattendrequelalameaitnide
tourner avant de relever la tête de coupe.
BA sl 8-10 lxu.indd 25 28.02.11 11:01
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach SL 1 0 LXU Woodster bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach SL 1 0 LXU Woodster in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5.1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info