782422
21
Verklein
Vergroot
Pagina terug
1/180
Pagina verder
21
and with an earthed type socket that fits the plug of this
machine at the other end.
Mounting the Tool
Note:
We highly recommend that you bolt this mitre saw se-
curely to a work bench to gain the maximum stability of
your machine.
• Locateandmarkthefourboltholesonthebench.
• Drillthebenchwithaø10mmdrillbit,
• Boltthemitresawontothebenchwithbolts,washers
and nuts. Note that these fasteners are not supplied
with the machine.
Operating the Tool
WARNING! Never connect the plug to the power source outlet
until all Installations and adjustments are completed and
you have read and understood the safety and operational
instructions.
Basic Pullover Mitre Saw Operations
• Alwaysusetheclamp17toholdtheworkpiecermly.
2 holes are provided for the clamp.
• Alwayspositiontheworkpieceagainstthefence.Any
piece that is bowed or warped and cannot be held flat
on the table or against fence may trap the blade and
should not be used.
• Neverplacehandsnearthecuttingarea.Keephands
outside the ”No Hands Zone” which includes the entire
table and is labelled by ”No Hands” symbols.
WARNING! To avoid injury from materials being thrown, un-
plug the saw to avoid accidental starting, and then remove
small materials.
Chop Cut (Fig. 6)
• Forchop cutting,slide thecuttinghead tothe rear
position as far as it will go, and lock the carriage 1 by
the lock handle 2.
courant et, à l’autre extrémité, d’une fiche femelle avec
mise à la terre, qui s’enfiche dans la scie.
Montage de la scie
N. B.:
Il est vivement recommandé de boulonner la scie à un
établi pour lui assurer le maximum de stabilité.
• Repéreretmarquerl’emplacementdesquatretrousde
fixation sur l’établi.
• Percer les trous dans l’établi avec un foret de 10
mm.
• Boulonnerlascieàl’établiàl’aidedeboulons,ron-
delles et écrous (non fournis avec la scie).
Mode d’emploi
ATTENTION! Ne pas enficher la fiche dans une prise de cou-
rant avant d’avoir terminé toutes les étapes de l’installation
et du réglage et d’avoir lu et compris les consignes de sé-
curité et le mode d’emploi.
Consignes générales
• Toujoursutiliserleserre-joint17pourimmobiliserla
pièce à scier. 2 trous sont prévus pour le serre-joint.
• Toujoursplacerlapièceàcoupercontreleguide.Ne
pas utiliser de pièce cintrée ou tordue ou de pièce qu’il
est impossible de maintenir à plat sur le plateau ou
contre le guide, car elle risque de bloquer la lame.
• Nejamaisplacerlesmainsdanslazonedecoupe,qui
comprend l’ensemble du plateau et est indiquée par
des symboles „Pas de mains”.
ATTENTION! Pour éviter d’être blessé par des projections de
matériaux, débrancher la scie pour l’empêcher de se mettre
en marche accidentellement et enlever les petits morceaux
de matériaux.
Coupe de refend (Fig. 6)
• Pourlacoupederefend,faireglisserlatêtedecoupe
vers l’arrière aussi loin qu’elle peut aller et bloquer le
chariot 1 à l’aide de la manette de blocage 2.
BA sl 8-10 lxu.indd 21 28.02.11 11:01
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach SL 1 0 LXU Woodster bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach SL 1 0 LXU Woodster in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5.1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info