757755
31
Verklein
Vergroot
Pagina terug
1/111
Pagina verder
to Contents
Detailed Settings Screen (JUPITER-8)
1
2
3
4 5 6 7
8
9 10 11
12
1 SystemSystem
CONDITION
Simulates the changes that occur as a unit ages.
PITCH DRIFT
Adjusts the slight pitch drift that occurs when notes are
played on an analog synthesizer.
KEY MODE
[SOLO] button
Sound is produced monophonically.
[POLY] button
Sound is produced polyphonically.
[UNISON] button
Sound is produced in unison.
[SL-UNISON] button
Sound is produced in monophonic unison.
PORTAMENTO [OFF] [ON] button (PORTA MODE/PORTA TIME)
Selects whether portamento is applied to the performance. Use the bar below to
specify the portamento time.
PORTA CRV
[ORIG] button
Change according to the original
curve of the model.
[LIN] button
Change in a linear curve.
[EXP-1] button
Change in a non-linear curve (gentle
slope).
[EXP-2] button
Change in a non-linear curve (steep
slope).
[PRM EXP] button
(PARAM EXPANSION)
If this is ON, the range of the LFO
RATE, CUTOFF, RESONANCE, and
FILTER ENV DEPTH parameters are
extended beyond the range of the
original model.
2 VCO-1VCO-1
[CROSS MOD] knob
Uses the OSC2 waveform to change
the frequency of OSC1. Higher values
cause the sound of OSC1 to be more
complex, allowing you to create
metallic sounds or sound eects.
[RANGE] knob (OSC1 RANGE)
Species the octave of OSC1.
16’, 8’, 4’, 2’
[WAVE FORM] knob
(OSC1 WAVE FORM)
Selects the waveform that is the basis
of the OSC1 sound.
TRI, SAW, PW, SQR
3 VCO-2VCO-2
[SYNC] button (SYNC SWITCH)
This is oscillator sync. It produces
a complex waveform by forcibly
resetting OSC1 to the beginning of
its cycle in synchronization with the
cycle of OSC2.
[FINE TUNE] knob
(OSC2 FINE TUNE)
Species a ne adjustment to the
pitch of OSC2.
OSC2 MODE
[NORMAL] button
OSC2 operates as NORMAL
(audible frequency range).
Use the [RANGE] (OSC2 RANGE)
knob to set the frequency.
-12–+24
[LOW FREQ] button
OSC2 operates as LFO (low
frequency range).
Use the [LOW FREQ] knob to set
the frequency. 0–127
[WAVE FORM] knob
(OSC2 WAVE FORM)
Selects the waveform that is the
basis of the OSC2 sound.
SINE, SAW, PW, NOISE
4 MIXERMIXER
[VCO-1] knob (OSC1 LEVEL)
Adjusts the volume balance of OSC1.
[VCO-2] knob (OSC2 LEVEL)
Adjusts the volume balance of OSC2.
5 VCFVCF
[R] [M] [S] buttons
(VINTAGE FLT TYPE)
If a vintage type model is selected,
these buttons change the type
of lter.
[R] models a Roland lter, and [M]
and [S] model vintage synthesizers
made by other companies.
[HPF] knob
Adjusts the cuto frequency of the
high-pass lter.
[FREQ] knob (CUTOFF)
Species the cuto frequency of
the low-pass lter. The frequency
region above the cuto frequency is
cut, producing a more mellow tonal
character.
[RES] knob (RESONANCE)
Boosts the region of the lters cuto
frequency. Higher values produce a
stronger result, giving the sound a
distinctively synthesizer-like character.
SLOPE (FILTER SLOPE)
Selects the type of slope for the low-pass lter.
-12dB/OCT, -24dB/OCT
[ENV-1] [ENV-2] buttons (FLT ENV MODE)
Selects the envelope that is used to control the ENV-1/
ENV-2 cuto frequency.
ENV MOD (FLT ENV DEPTH)
Adjusts the amount by which the cuto frequency is
controlled by the envelope.
FILTER MOD
Adjusts the amount by which the LFO modulates the
cuto frequency.
KEY FOLLOW (FLT KEY FOLLOW)
Adjusts the amount by which the keyboard pitch aects
the cuto frequency (key follow). With smaller values, the
cuto frequency becomes lower as you play higher notes.
6 VCAVCA
[LEVEL] knob (AMP LEVEL)
Adjusts the volume of the tone.
LFO MOD (AMP MOD STEP)
Uses the LFO to vary the AMP volume (tremolo eect).
Higher values produce a greater eect.
7 LFOLFO
WAVEFORM (LFO WAVEFORM)
Selects the waveform of the LFO.
SINE, SAW-DW, SQR, S&H
RATE (LFO RATE)
Species the rate of the LFO cycle.
DELAY TIME (LFO DELAY TIME)
Adjusts the time from when the key is pressed until the
LFO starts to apply modulation.
8 VCO MODULATORVCO MODULATOR
LFO MOD
Adjusts the depth at which the LFO
modulates the OSC.
ENV MOD (PIT ENV DEPTH)
Adjusts the depth at which the LFO
modulates the ENV1.
FREQ MOD (DEST SELECT)
Selects the OSC that is modulated
by LFO MOD.
Select buttons (PW MODE)
Species the pulse width mode.
LFO : The pulse width is changed
by the LFO.
MANUAL: The pulse width is changed
by the slider.
ENV : The pulse width is changed by
the ENV1.
Slider (PULSE WIDTH MOD)
Adjusts the amount of pulse width
change.
9 ENV-1 (Envelope) ENV-1 (Envelope)
Envelope
You can directly drag the curve in the screen to edit the
ADSR settings of the envelope in a visual way.
AD
SR
The values of the [A] [D] [S] [R] knobs also change in
tandem.
To make ne adjustments, hold down the [shift] key
while you drag.
[A] knob (ENV1 ATTACK)
Adjusts the Attack time.
[D] knob (ENV1 DECAY)
Adjusts the Decay time.
[S] knob (ENV1 SUSTAIN)
Adjusts the Sustain level.
[R] knob (ENV1 RELEASE)
Adjusts the Release time.
KEY FOLLOW
(ENV1 KEY FLW SW)
Species the ENV1 key follow. If key
follow is on, ADR times become
longer for lower notes and shorter for
higher notes.
POLARITY
Species the polarity of the envelope.
10 ENV-2 (Envelope) ENV-2 (Envelope)
Envelope
You can directly drag the curve in the screen to edit the
ADSR settings of the envelope in a visual way.
AD
SR
The values of the [A] [D] [S] [R] knobs also change in
tandem.
To make ne adjustments, hold down the [shift] key
while you drag.
[A] knob (ENV2 ATTACK)
Adjusts the Attack time.
[D] knob (ENV2 DECAY)
Adjusts the Decay time.
[S] knob (ENV2 SUSTAIN)
Adjusts the Sustain level.
[R] knob (ENV2 RELEASE)
Adjusts the Release time.
KEY FOLLOW (ENV2 KEY FLW SW)
Species the ENV2 key follow. If key follow is on, ADR times become longer for
lower notes and shorter for higher notes.
11 MFXMFX
MFX parameters
The edit screen is dierent for each MFX type.
& For details, refer to MFX Parameters.
[MFX] button
Turns MFX on/o.
[MFX TYPE] indication
Shows the currently selected
MFX name.
To change the MFX, click the MFX
name and choose from the list that
appears.
[MFX LEVEL] knob
Adjusts the MFX output level.
12 ControllerController
A.TOUCH [LEVEL] knob
Species how the volume of the tone is aected by
aftertouch.
A.TOUCH [FREQ] knob
Species how the frequency of the low-pass lter is
aected by aftertouch.
A.TOUCH [LFO] knob
Species how the LFO depth is aected by aftertouch.
BEND [PIT] knob (BEND PITCH)
Species the range of pitch change produced by pitch
bend.
BEND [FILT] knob (BEND FILTER)
Species the range of lter change produced by pitch
bend.
MOD [LFO] knob (MODULATION LFO)
Species the amount of LFO applied by modulation.
Model Screen (JUPITER-8)
KEY MODE
[SOLO] button
Sound is produced monophonically.
[POLY] button
Sound is produced polyphonically.
[UNISON] button
Sound is produced in unison.
[SL-UNISON] button
Sound is produced in monophonic unison.
Right-click
LEARN MIDI CC
Assigns a control change to each
button.
[CUTOFF] knob
Adjusts how far the lter is open.
Higher values make the sound brighter, and lower values
make the sound darker.
[RESO] knob
Emphasizes the portion of the sound in the region of
the cuto frequency, adding character to the sound.
Excessively high settings can produce oscillation, causing
the sound to distort.
Increasing this value strengthens the character, and
decreasing it weakens the character.
[ATTACK] knob
Species the time from when the key is pressed until the
sound completes its attack.
Higher values produce a softer attack, and lower values
produce a sharper attack.
[RELEASE] knob
Species the time from when the key is released until the
sound disappears.
Higher values produce a longer release, and lower values
produce a crisper release.
[CROSS MOD] knob
Uses the OSC2 waveform to change the frequency of
OSC1. Higher values cause the sound of OSC1 to be more
complex, allowing you to create metallic sounds or sound
eects.
How to operate the knobs
Right-click
LEARN MIDI CC
Assigns a control change to the
parameter selected by [CUTOFF]–
[CROSS MOD].
Drag Tone edit
Edits each parameter.
[EDIT] button
Switches between the small screen
and detailed settings screen.
[WRITE] button
Accesses the Tone/Drum Kit Manager,
allowing you to save a tone or
drum kit.
[OVERWRITE] button
Overwrite-saves the settings.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Roland Zenology bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Roland Zenology in de taal/talen: Engels als bijlage per email.

De handleiding is 29,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info