DD
DD
RR
RR
YY
YY
II
II
NN
NN
GG
GG
CC
CC
YY
YY
CC
CC
LL
LL
EE
EE
Warning: make the drying cycle with the
water container empty.
The drying cycle eliminates possible water
particles present in the filters and in the suc-
tion tubes of the container (5). The purpose
of this process is to avoid interventions of
the humidity sensor, which interrupts the op-
eration of the appliance.
The humidity sensor acts in protection of the
Hepa filter preventing humidity particles from
reaching it, damaging its function.
• Move the two air outlet filter grill opening
levers (18) at the same time by pushing
them towards the inside (fig.15) so as to
allow the air outlet filter grill (17) to un-
hook.
• Remove the Hepa filter (19) as described
in the "Cleaning or replacing the Hepa fil-
ter" paragraph.
• Remove the back sponge filter (19a).
• Connect the supply cable plug (27) to the
mains.
• The first stage of the suction power indica-
tor lights (13) on the handle will start to
flash.
• To reactivate the appliance, keep the
mains ON/OFF switch (11) pushed until
the machine reaches the maximum speed.
• The appliance will keep on working as
long as the humidity sensor feels the pres-
ence of water in the circuit.
• When the sensor no longer feels water in
the circuits of the appliance, it will auto-
matically go to the stand-by position and
the indicator lights (13) will start to flash.
• Put the Hepa filter (19) and the air outlet
filter grill (17) back in place.
• If you want to use the appliance again, fill
the water container (5) as indicated in the
"Preparation for use" paragraph, other-
wise store the appliance with the container
(5) empty.
HH
HH
UU
UU
MM
MM
II
II
DD
DD
II
II
TT
TT
YY
YY
SS
SS
EE
EE
NN
NN
SS
SS
OO
OO
RR
RR
• If the sensor measures some humidity, the
machine will stop and the 4 lights on the
indicator lights (13) will start to flash alter-
nately first to last and viceversa.
• To reactivate the appliance, keep the
mains ON/OFF switch (11) pushed until
the machine reaches the maximum speed.
• The appliance will keep on working as
long as the humidity sensor feels the pres-
ence of water in the circuit.
• When the sensor no longer feels water in
the circuits of the appliance, it will auto-
matically go to the stand-by position and
the indicator light (13) will start to flash.
• Reassemble the Hepa filter (19) and the
air outlet filter grill (17), inserting first the
two pins (18a) into the locking holes (18b)
(fig.16).
Warning: make the drying cycle with the
water container empty.
UU
UU
SS
SS
II
II
NN
NN
GG
GG
TT
TT
OO
OO
OO
OO
LL
LL
SS
SS
Tools may be connected directly to the hose
(D) or to the telescopic tube (A).
Using the telescopic tube (A)
The tube is about 60 cm long when closed, 1
m when extended to its greatest length. To
increase or decrease length, press the catch
positioned as shown in fig. 6 and extend or
reduce length as desired.
Using the joker brush (M)*
The Joker brush may be used to vacuum up
solids or a limited amount of liquids on any
kind of surface.
Using the parquet accessory (N)*
Position the Joker brush (M) on the parquet
accessory (N) as shown in figure 17. Apply
the tool to the brush, following the direction
of the arrow so that it is aligned properly and
they connect together.
To release the parquet accessory from the
Joker brush, pull the two levers on the sides
of the frame outward and lift the brush
(fig.18).
* (optional for mod. AS800)
Using the universal brush (B)
Connect the brush to the telescopic tube. If
you move the selector on the brush (B1)
Lecologico Compact AS800 - AS801
43
