Handleiding Parkside PKO 270 A1 - IAN 96894 (pagina 10 van 44) (Nederlands, Duits, Engels, Frans)

595284

Verklein

Vergroot

Pagina terug

1/44

Pagina verder

5GB/IE

7. Before starting the equipment

Before you connect the equipment to the mains supp-

ly make sure that the data on the rating plate are iden-

tical to the mains data.

• Check the equipment for damage which may have

occurred in transit. Report any damage immediately

to the transport company which was used to deliver

the compressor.

• Install the compressor near the point of consumpti-

on.

• Avoid long air lines and supply lines (extension ca-

bles).

• Make sure that the intake air is dry and dustfree.

• Do not install the compressor in a damp or wet

room.

• The compressor may only be used in suitable rooms

(with good ventilation and an ambient temperature

from +5 °C to 40 °C). There must be no dust, acids,

vapors, explosive gases or inammable gases in the

room.

• The compressor is designed to be used in dry

rooms. It is prohibited to use the compressor in are-

as where work is conducted with sprayed water.

• The oil level in the compressor pump has to be che-

cked before putting the equipment into operation

(see 10.4).

8. Attachment and operation

n Important!

Remove the transportation braces (between the

compressor pump and cladding, see Fig. 7) prior

to initial start-up. If the transportation braces are

not removed, heat can build up and cause the

compressor to ignite.

n Important!

You must fully assemble the appliance before us-

ing it for the  rst time!

You will require the following tools for assembly and

installation: 2 x open-ended wrench size 13 mm (not

included)

8.1 Fitting the wheels (11)

• Fit the supplied wheels as shown in Figure 5.

8.2 Fitting the supporting foot (8)

• Fit the supplied supporting foot as shown in Figure 6.

8.3 Fitting the air lter (15)

• Remove the transportation stop (B) and screw the

air  lter (15) to the equipment. (Fig. 7, 8).

8.4 Changing the transportation cover (A)

• Remove the transportation cover from the oil lter

opening (21) and insert the supplied oil sealing plug

(16) into the oil  ller opening. (Fig. 9, 10.)

8.5 Mains connection

• The compressor is equipped with a mains cable

with shock-proof plug. This can be connected to any

230V ~ 50 Hz shock-proof socket which is protected

by a 16 A fuse.

• Before you use the machine, make sure that the

mains voltage is the same as the operating voltage

(see the rating plate).

• Long supply cables, extensions, cable reels etc.

cause a drop in voltage and can impede motor start-

up.

• At low temperatures below +5°C, sluggishness may

make starting difcult or impossible.

8.6 ON/OFF switch (Fig. 2)

• Pull the ON/OFF switch (17) upwards to switch on

the compressor. To switch off the compressor, press

the ON/OFF switch down.

8.7 Setting the pressure (Fig. 1-3)

• Use the pressure regulator (3) to set the pressure on

the pressure gauge (5).

• The set pressure can be drawn from the quicklock

coupling (4).

• The vessel pressure can be read off the pressure

gauge (6).

• The vessel pressure is drawn from the quicklock

coupling (20).

8.8 Setting the pressure switch (Fig. 1)

• The pressure switch (2) is set at the factory. Cut-in

pressure approx. 6 bar Cut-out pressure approx. 8

bar.

8.9 Fitting the compressed air hose (Fig. 1, 3)

• Use the compressed air hose (14) if you intend to

carry out work at a greater distance from the com-

pressor. To do so, connect the nipple (H) on the

compressed air hose to one of the quickrelease cou-

plings (4, 20). Then attach the compressed air tool

to the quick-release coupling (G) on the compressed

air hose.

9. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Parkside PKO 270 A1 - IAN 96894 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info