31254
25
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
- 25 -
Setup: Connecting the SCSI Cable
SCSI Connection Checklist
Turn off the computer, the LS-2000, and all SCSI devices
before connecting the scanner.
Be sure that the devices at both ends of the SCSI chain are
terminated. If the host computer is a Macintosh, the chain
will already be terminated at the computer end. In the case
of IBM PC/AT compatibles in a chain which contains external
devices only, the chain should be terminated at the SCSI
board. In the case of a chain which includes internal devices,
you may need to remove termination from the board and
terminate the last internal device.
The maximum number of SCSI devices that can be con-
nected in a single chain is eight, including the computer and
any internal SCSI devices such as hard disks or CD-ROM
drives.
The total length of cabling in the SCSI chain should be no
more than six meters (twenty feet). The longer the cabling,
the less reliable the connection.
When using a SCSI extension board with an IBM PC/AT
compatible computer, be sure that you have the latest
available driver software for your board. If you experience
trouble with SCSI connections, contact the manufacturer to
learn whether an updated driver has been released.
Setting the SCSI ID
Each device in the SCSI chain has a unique ID, which is a num-
ber between zero and seven that the computer uses to distin-
guish between different devices. When connecting the LS-2000
to a SCSI chain, the scanner’s SCSI ID must be set to a number
that is not shared by any of the other devices, including the
computer itself.
The scanner’s SCSI ID is indicated by the SCSI ID dial on the
rear panel. Before the scanner leaves the factory, the ID is set
to “2.”
SCSI ID
6
5
4
3
2
1
0
7
When choosing
another ID for the scanner, bear in mind that
the computer will usually have an ID of either “0” or “7,” and
that internal hard disks often have IDs of “0” or “1.” In the case
of Macintosh computers, the computer will have an ID of “7,”
while the internal hard disk and CD-ROM drive often have IDs
of “0” and “3,” respectively. In general, it is recommended that
you set the scanner’s ID to any number other than zero, one,
three, and seven that is not used by another SCSI device.
Caution: Assigning the same ID to two different devices
could render the computer system inoperable or result in important
data on a hard disk being lost or corrupted.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nikon COOLSCAN_LS2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nikon COOLSCAN_LS2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Nikon COOLSCAN_LS2000

Nikon COOLSCAN_LS2000 Gebruiksaanwijzing - Deutsch - 45 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info