31254
22
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
- 22 -
Setup: Connecting the SCSI Cable
SCSI devices are connected to the computer in a “daisy chain.”
Up to eight devices, including the computer and any internal
SCSI devices such as hard drives and CD-ROM drives, can be
connected in a SCSI chain. The first and last devices in the
chain must be terminated, i.e., fitted with special circuitry to
reduce noise, making the connection more reliable. If the
LS-2000
is the last device in the chain, it can be terminated
using the termination switch on the rear of the scanner. Except
in the case of some laptop computers requiring external termi-
nators, the other end of the chain will be terminated inside the
computer, either at the SCSI adapter or at an internal drive. In
the case of IBM PC/AT computers with internal SCSI devices, it
may be necessary to remove termination from the SCSI adapter
board before connecting external devices.
To connect the scanner to the SCSI chain, a SCSI cable with a
male half-pitch 50-pin connector is required. The other end of
the cable must match the connector on the devices to which
the scanner is to be connected. For direct connection to most
Macintosh computers, a 25-pin D-sub connector will be re-
quired (Macintosh laptop computers use a different type of
connector). SCSI boards for IBM PC/AT computers will usually
be provided with a 25-pin D-sub connector, a 50-pin Centronics
connector, or a half-pitch 50-pin connector with the pins ar-
ranged in two separate rows or attached to a central “finger.” If
the correct type of cable is not available, an adapter can be
attached to one or both ends of the cable. To prevent interfer-
ence, SCSI cabling should be of a high-impedance type and be
as short as possible. The total length of cabling in a SCSI chain
must not exceed six meters (twenty feet), but be aware that
the reliability of the SCSI interface will drop as the length of the
cable increases.
A SCSI cable is provided with scanners sold in the United States
and Canada. If your scanner was purchased in another region,
before connecting the SCSI cable you should attach the ferrite
core provided with your scanner (the cable provided to cus-
tomers in the United States and Canada does not require a
core). Place the SCSI cable in the center of the open core and
close the core tightly. The core should be attached as far as
possible from the scanner; i.e., as close as possible to the other
device to which the cable is attached. Attach the plastic tie on
the scanner side of the core to prevent the core from sliding
out of position.
1. Close and latch core
To LS-2000
2. Place tie around cable
and pull tight
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nikon COOLSCAN_LS2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nikon COOLSCAN_LS2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Nikon COOLSCAN_LS2000

Nikon COOLSCAN_LS2000 Gebruiksaanwijzing - Deutsch - 45 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info