653744
6
Verklein
Vergroot
Pagina terug
1/23
Pagina verder
•Fit the retainer (4) to ensure that the mixing decrease, you can increase the rotating speed
paddle is locked in position.
of the paddle by turnig the knob (7).
•Verify that the flat gate (9) is in closed position.
•In order to extrude the last portion of ice
cream, stop the paddle by operating the knob
•Pour the ice-cream mixture previously
(2), lift the cover (3) and patch the residual ice
prepared intothe bowl.
cream on the bottom of the bowl. Proceed
again with the extrusion procedure.
IMPORTANT: if the appliance switches off, due
•Once the extrusion process is terminated,
to a temporary power blackout, or because the
close the extrusion gate with the handle (9).
refrigeration switch was accidentally turned off,
ATTENTION! The extrusion time strictly
wait five minutes before restarting. The
depends from the ice cream hardness. An hard
refrigeration circuit has a special safety device
ice cream will thake longer time to extrude.
preventing the compressor to restart until cool,
Under certain circumstances, the power
as to avoid damages to the unit.
required to start the extrusion process may
•Close the transparent lid (3) over the bowl.
cause the motor thermal protection trip. In this
•To start the paddle movement, rotate the knob
case, power off the motor, wait a few minutes in
(2) clockwise. Set the rotating speed near the
order to allow to the ice cream becoming softer
half of maximum by rotating the knob (7).
and power on the motor again: the extrusion
Preparation time varies according to quantity,
process will restart.
temperature of the mix, type of ice cream
(cream-style or sherbet), and room
HELPFUL HINTS
temperature.
•Ingredients should preferably be pre-chilled to
IMPORTANT: Movement of the mixing paddle is
refrigerator temperature; this will shorten ice-
completely independent from the freezing
cream making times.
system. A safety device stops automatically the
•For better results, start refrigeration by turning
paddle when the lid is not in closed position.
the knob (1) 5 minutes before pouring in the
•Depending on the quantity of ingredients and
ingredients.
recipe used you will have a delicious fresh ice
•To allow volume to increase of the mixture, do
cream in 10/15 minutes.
not fill the container to more than half its
•By the opening (3a) on the cover, you can add
capacity (use max. 2,5 Kg of ingredients).
some ingredients during the preparation of the
•The GELATO PRO 10K ice-cream maker has a
ice cream.
powerful refrigeration system. Do not leave
•When the ice cream has reached the desired
the ice cream in the container for too long with
consistency, is now possible to proceed with
the refrigeration on, you might find it frozen!
the extrusion operation.
CLEANING THE BOWL
EXTRUSION OF THE ICE CREAM
Cleaning the bowl of GELATO PRO 12K is very
Proceed as described:
easy. Proceed as follows:
•Prepare the ice cream tray on the bracket (8).
•Once the paddle is removed, turn off the
•Turn off the freezing plant by rotating the knob
freezing plant and simply put inside the bowl 2
(1).
litres of warm water.
•Open the extrusion system by pull out the flat
•Wash out the bowl with a sponge. Do not use
gate (9).
sharp utensils inside the bowl!
•Rotate counterclockwise the knob (2). The
•Pout an empty container of at least 3 litres
paddle will turn clockwise starting the
capacity under the chute (11).
extrusion process.
•Open the extrusion system by pulling the flat
•When the quantity of the ice cream in the bowl
•Turn on the knob (1) to start cooling.
English English
gate (9); the water will flow on the container TROUBLESHOOTING
The refrigeration system fails to work:
below.
•Check that the plug is correctly inserted in the
•If necessary, repeat the cleaning cycle until the
mains and that the appliance is receiving
bowl will be clean. Clean the bottom of the
electricity. Restart the ice-cream maker.
bowl with a sponge.
•The compressor safety device has been
•Dry the carefully the ice cream maker bowl
tripped. Wait 5-10 minutes before restarting
with a cloth in order to avoid any dirty deposit.
the appliance. Continuous, premature
APPLIANCE CLEANING AND MAINTENANCE
attempts to restart the appliance simply
•Before starting to clean make sure that the
prolong the time before it can be put back into
machine is switched off (power switch (10) in
use.
OFF position) and unplugged.
•Check that the appliance is correctly
•Wash the paddle (5), the transparent lid (3)
positioned on a horizontal surface with the
and the locking nut (4), in a soapy warm water.
ventilation slots free from all obstacles.
•To better clean the paddle, remove the plastic
The mixing paddle does not turn:
inserts by pulling it from his site.
•Check that it is correctly connected to the
•If the inserts are worn out, they must be
sleeve, and fixed in place with the fixing nut
replaced to prevent the mixing action from
(4).
becoming less effective. These parts are
•Check that there are no obstacles preventing it
available from all authorised service centres.
from turning.
•In order to clean the transparent lid (3), is
•Make sure that the cover is in correct closed
possible to leave it out from the machine by
position: the safety device stops the paddle if
removing the hinge.
the cover is lifted.
•Clean the chute (11) and the frame (8). Leave
The appliance is excessively noisy:
it out from his site by unscrewing the
•A certain level of noise during operation is
aprropriate screws (12) and (14). Clean
normal. If it becomes excessive, contact an
carefully the surrounding area.
authorized service centre.
ATTENTION: when mounting the pieces, the
Extrusion procedure is very slow:
screws must be tightened by hands.
•The ice cream is too hard. Turn off the freezing
•Clean carefully the extrusion system by
plant, wait a few minutes and try again.
leaving out the flat gate support (9). Unscrew
the appropriate screws (13). Clean carefully
the gasket and the surrounding zone. Check
the integrity of the gasket: an excessive wear
can cause a mixture leakage during ice cream
making operations.
ATTENTION: when mounting the pieces, the
screws must be tightened by hands.
•Clean the body of the appliance and non-
removable parts with a specific product.
IMPORTANT: never wash the appliance with
jets of water! - it contains electrical parts.
•Before storing the appliance, clean it with an
absorbent cloth.
•One time every year at least clean the
ventilation slot.
ATTENTION: Pls keep the packaging boxes. They
will be necessary in case you should return the
machine for repair or you should return it for any
other reason. If the machine will be sent back with
a packaging box not suitable for transportation all
repairing charges will be at charge of the sender,
even if the machine is under warranty. If the
machines doesn't need to be repaired and the
package will not be suitable the machine will be
returned to the sender too.
76
Materials and articles destined for use in contact with
food products are conform to the EC Regulation
1935/2004. This appliance complies with the
requirements of the Low Voltage Directive
2006/95/CE, and the Electromagnetic Compatibility
Directive 2004/108/CE.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nemox GELATO PRO 12K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nemox GELATO PRO 12K in de taal/talen: Duits, Engels, Italiaans, Spaans als bijlage per email.

De handleiding is 5,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info