Handleiding NAD M12 (pagina 16 van 22) (Engels)

667813

Verklein

Vergroot

Pagina terug

1/22

Pagina verder

LEARNING CODES FROM OTHER REMOTES

Begin by positioning the HTRM 2 “nose-to-nose” with the source remote so

the two devices’ infrared windows are about 2 inches apart.

• Enter Learning Mode: On the HTRM 2, simultaneously press-and-hold

for 3 seconds both a Device Selector key and the [RES] key until the

Learn LED (located between HTRM 2’s ON and OFF buttons) turns

steady green.

• Press the HTRM 2’s function key you wish to teach a command; the

Learn LED will turn amber.

• Press-and-hold the function key on the source remote: The HTRM 2’s

Learn LED will icker amber for a second or two, then turn solid green.

The command is learned.

• Press the HTRM 2’s Device Selector key again to exit the learning mode.

If the Learn LED does not icker amber you may need to vary the distance

between the remotes. If the Learn LED turns red rather than green, that

particular command of that source remote command could not be learned.

Example: Learning “BD Pause”

Position the HTRM 2 and your BD player’s remote as described above.

• On the HTRM 2, simultaneously press-and-hold [BD] and [RES]; the Learn

LED turns steady green.

• Press the HTRM 2’s Pause [ j ] key; the Learn LED turns amber.

• Press-and-hold the corresponding Pause key of your BD player’s remote

control; the HTRM 2’s Learn LED ickers amber and then turns solid

green. The command is learned.

• Press [BD] again to exit the learning mode.

NOTES

• The DEVICE SELECTOR keys can themselves be congured to learn a command.

• Press and hold a congured DEVICE SELECTOR for at least 2 seconds to

execute a function assigned to the particular DEVICE SELECTOR key.

• Short press of a congured DEVICE SELECTOR will just switch the active device.

CANCEL OPERATION

You can cancel conguring a key, by pressing the active Device Selector key

before the learn process is complete; the Learn LED will turn red.

PUNCH THROUGH

The HTRM 2’s “punch-through” function allows you to retain a function key

from one Device Select “page” to another, so that, for example, the AMP

[SURR MODE] function might still control the M12 when the BD Device

Selector page is active.

NOTE

The HTRM 2’s [VOL R/T] keys are pre-programmed as “punched-

through” for all Device Selector pages: [VOL R/T] will operate the

M12’s master-volume regardless of the currently selected device. The

[SURR] [CENT] and [SUB] Channel Volume controls similarly are pre-

programmed as punched-through.

To set a punch through, after entering the Learning Mode, and pressing the

desired key to be punched through, simply press the device key twice of

the device to punch through to. The status LED will turn green; press the

Device Selector key again to exit Learning Mode.

Example: Punch-through AMP [SURR MODE] key to the BD “page”

• On the HTRM 2, simultaneously press-and-hold [BD] and [RES]; the Learn

LED turns steady green.

• Press [SURR MODE]; the Learn LED turns amber.

• Press [AMP] twice; the Learn LED turns green.

• Press [BD] again to exit the learning mode.

COPY A COMMAND FROM ANOTHER KEY

You may copy a command from any HTRM 2 key to any other. To copy a key

function, after entering the Learning Mode, and pressing the desired key

to be copied to, simply press the device key from which you wish to copy,

having rst pressed its Device Selector key if it resides on another “page.”

The status LED will turn green; press the Device Selector key again to exit

Learning Mode.

Example: Copy the Pause command from the CD page to the AMP [ j ]

button:

• On the HTRM 2, simultaneously press-and-hold [AMP] and [RES]; the

Learn LED turns steady green.

• Press Pause [ j ] ; the Learn LED turns amber.

• Press [CD]; press Pause [ j ] ; the Learn LED turns green.

• Press [AMP] again to exit the learning mode.

NOTE

The copy and punch-through functions are similar. However, if you

copy a command and then subsequently delete, or over-write the

original (source-key) command , the copied-to key’s command remains

unchanged. If you punch-through to a command and then delete or

over-write the original key, the punched-through functions also change

accordingly.

MACRO COMMANDS

A “macro” command is a series of two or more remote codes issued

automatically from a single keypress. You might use a macro to automate a

simple command sequence, such as, “Turn on the BD player and then press

PLAY”. Or you might compose an elaborate macro to power up an entire

system, select a source, choose a Listening Mode, and begin playback—

again, all from a single keypress. Each DEVICE SELECTOR and function keys

of the HTRM 2 can be stored one macro.

NOTE

Macros are independent of the currently selected device.

RECORDING MACROS

To record a macro, simultaneously press-and-hold for 3 seconds both the

[MACRO] key and the HTRM 2 function key to which you wish to assign the

macro, until the status LED turns green. The macro button will also light up.

Press the sequence of function keys to be recorded into the macro, being

sure to rst press the requisite Device Selector key for each function (you

may switch devices while recording the macro as many times as necessary),

allowing you to create macro containing commands from more than one

Device Selector “page.”

When you have nished entering the desired command sequence, press

[MACRO] again to store the macro; the Learn LED and [MACRO] key

illumination will turn o.

NOTE

Each macro can store a maximum of 64 command steps. If you exceed

this number, the macro will be stored automatically after the 64th

command is added.

OPERATION

USING THE HTRM 2 REMOTE CONTROL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

NAD M12 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van NAD M12

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info