WARNING - To reduce the risk of re or electric shock, do not expose this appliance to
rain or moisture.
If at any time in the future you should need to dispose of this product please note
that Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer
for recycling advice.(Waste Electrical and Electronic Equipment Directive)
ATTENTION: To reduce the risk of electric shock, do not remove
the cover. There are no user serviceable parts inside the unit. Re-
fer all servicing to qualied personnel.
GB - 19
WARNINGS
GB - 17GB - 16GB - 15
GB - 13
GB - 12
GB - 11GB - 10
The exclamation point within the triangle is a warning sign alerting the user of
important instructions accompanying the product.
The lightening ash with arrowhead symbol within the triangle is a warning sign
alerting the user of “dangerous voltage” inside the unit.
PI: SOUND/MUTE
While AF switching is implemented in C201 station, AF can switch to 100 MHz, which is
non genuine AF (where, different PI with same AF) in short “DIP”.
If a car cruises that critical area back and forth, an oscillation phenomenon can be oc-
curred, because the different PI code can be received from 100 MHz with “XXX” PI.
The car radio has special procedure to reduce even this kind of unavoidable situation
however there is a limit to be escaped from this serious case perfectly.
In that serious case, 2 mode is selectable as follows:
- PI SOUND mode:
When above different PI sound (DIP) is heard once in a while, the DIP’s sound will be
heard for a short time.
- PI MUTE mode:
Under above same situation, a mute sound will be heard for a short time.
RETUNE: LONG/SHORT
When PI information gets lost at the current station for retune time which is set by RE-
TUNE SHORT (30 sec.) or RETUNE LONG (90 sec.), the radio start to retune to next
same PI station.
MASK: DPI/ALL
MASK DPI mode: masked only the AF which has Different PI (DPI).
MASK ALL mode: masked the AF which has Different PI and NO RDS signal with high
eld strength.
EONTA DX/LO (DISTANCE/LOCAL)
The purpose of this function is to reduce unwanted EON TA switching, which EON TA
information was received from current station and the radio switched to that EON linked
station, but no information could not be received because the EON linked station is
located too far from that area. So the radio is switched back to current station again. In
above operation, a customer listens to a wrong program or mute sound for a while.
EON TA LOCAL mode
When the led strength level of EON linked is less than threshold level, the radio does
not switch that station, and a customer can hardly listen to any disturbances.
When EON TA LOCAL mode is selected, “EON TA LO” on numeric display is indicated
for a few seconds.
EON TA DISTANCE mode
EON TA switch is tried to implemented by the information of current station.
When EON TA DISTANCE mode is selected, “EON TA DX” on display is indicated for a
few seconds.
TA-VOLUME: Volume 30 (the default TA volume value is 30). You can set it to another value.
LISTENING TO USB/SD
To insert an USB device (not included)
Connect your USB device to the USB port on front panel. It will switch to “USB” mode
and start playback automatically.
To insert a SD/MMC card (not included)
Detach the front panel and insert a SD/MMC card to the card slot. Install the front panel
again. It will switch to “SD” mode and start playback automatically.
Basic player functions
Play/pause: press 1/ to suspend momentarily the playing track. Press again to re-
sume playback.
Skip/fast search: press to skip forward to next track or press to skip backward
to previous track. Press and hold or to search quickly within a track.
Intro scan:
Press 2/SCN button to play rst 10 seconds of each track, and “S-SCN” appears on
display. Press again to cancel intro playback and “S-SCN” disappears.
Press and hold 2/SCN button to play rst 10 seconds of each track in the current folder,
and “D-SCN” appears on display. Press again to cancel and “D-SCN” disappears.
Repeat:
Press 3/RPT button once to repeat your desired track, and “S-RPT” appears on display.
Press it again to cancel, and “S-RPT” disappears
Press and hold 3/RPT button to repeat all tracks in the current folder, and “ D-RPT” ap-
pears on display. Press it again to cancel, and “D-RPT” disappears.
Random playback:
Press 4/SHF button to play all les in random order, and “S-SHF” appears on display.
Press again to cancel this function, and “S-SHF” disappears.
Press and hold 4/SHF button for 2 seconds to play all les in the current folder in ran-
dom order, and “D-SHF” appears on display. Press again to cancel this function, and
“D-SHF” disappears.
Directory selection: Press DIR-button or DIR + button to select directory downward or
upward. If the MP3 disc does not contain any directory, there is no function of pressing
DIR- button or DIR + button.
Searching a track in USB/SD:
- Search by track number:
1. Press AS/PS/SCH button once, the display will show “MP3 T* “. Press the number
button 0-9 to select the track number, and press SEL/VOL to conrm and start playback.
- Searching by Directory or File Name
The unit searches les and directories that have the same character which is inputted
by the user. Press the corresponding buttons listed on the below.
7) TALK (00~20):
You can set the Bluetooth volume at “TALK 00” item. Press T-MENU/TRANS repeatedly
to select “TALK 00”. Rotate SEL/VOL to adjust the value (00-20), then press SEL/VOL
to conrm.
TALK volume MAIN volume
00 = 60
01 = 62
02 = 64
……………………..
20 = 100
MAKING AN OUTGOING CALL VIA THE UNIT
1) Select a phone number from RECEIVED LIST, DIALED LIST, MISSED LIST or
PHONE BOOK (Refer to the T-MENU section), then press .
2) To make an outgoing call by inputting the phone number manually, rst press and
“CALL –)“ appears on display. Use 0~9, *, # buttons to enter the phone number you
want to dial and press
again.(Note: shortly press * button to input “*” character, press and hold it to input “+”
character). Then press button again to call the number.
Note: if you input the wrong number, shortly press button to clear it. Press and
hold button to clear all numbers.
• TRANSFER THE CALL BETWEEN MOBILE PHONE AND THE UNIT
During the talking mode, you can press and hold T-MENU/TRANS button to transfer
the phone call between the mobile phone and the unit. When making an outgoing call,
it’s not possible to transfer if the call is not being answered yet.
• BLUETOOTH AUDIO
The unit supports Bluetooth audio function. If your mobile phone can play stereo music,
when pairing is ok, you can choose this unit to play the stereo music. When pairing
successful (the Bluetooth symbol appears on display), press MODE/PAIR to access
Bluetooth audio mode, “BT AUDIO” appears on display. The audio le in your mobile
phone starts to play via the car radio.
• BT RESET
In BT AUDIO mode. press and hold LOU/BND/ button for 5 seconds until “ BT RE-
SET” appears on display. The Bluetooth settings will go back to its initial stage.
LISTENING TO AUXILIARY SOURCE
1. Connect your auxiliary source (e.g. mp3 player) to the AUX IN jack.
2. Press /MUTE button to turn the unit on.
3. Press MODE/PAIR to select AUX mode.
4. Start playback from your auxiliary source.
5. Adjust the volume to desired level.
6. Disconnect your auxiliary source from the Aux in jack, press MODE/PAIR button to
select other source.
BLUETOOTH FUNCTION
*Before operate the Bluetooth function, make sure your mobile phone supports Blue-
tooth function.
*For different model of mobile phone, Bluetooth emissive power has some difference.
To get the best conversation quality, it is recommended that the distance between the
mobile phone and the unit is within 3 meters (Max. 10 meters).
* Don’t put any metal object or any obstacle between the path of the mobile phone and
the unit.
* Use the external microphone during phone talk.
• PAIRING
1) When the unit is ON, press and hold MODE/PAIR button until “PAIRING” appears on
the display.
2) On the mobile phone, select the Bluetooth set-up. (Please refer to the instruction
manual of your mobile phone on how to operate Bluetooth.)
3) “CarBT” should appear in the list on your mobile phone. Select “CarBT” and then
input password “0000” .
4) When pairing is successful, “CONN OK” will appear on display. The Bluetooth sym-
bol appears on display. (Note: When you turn off the Bluetooth function in your mo-
bile phone, “DISCONN” appears on display.)
5) When pairing failed, “PAIR END” will appear on display. You can press and hold
MODE/PAIR button to try the pairing again.
• RECONNECTION
This unit is with auto-reconnection function. If your mobile phone has been paired with
the unit before, every time when you turn on the Bluetooth function in your mobile
phone, the unit will reconnect with your mobile phone automatically.
• T-MENU
When successfully paired, shortly press T-MENU/ TRANS button on the front panel to
enter the telephone menu, keep pressing this button or press / button to select
your desired item in following sequence: PRE NUM/ RECELVED / DIALED / MISSED /
PHONE BK / MANU ANS / TALK.
1)PRE NUM: You can save 10 phone-call to the phonebook 1.
*How to save the phonebook
a) Press T-MENU/TRANS to select PRE NUM. Rotate SEL/ VOL . “EMPTY 0” appears
on display. Keep rotating the SEL/VOL to select desired preset number location (0-9).
Then press SEL/VOL to conrm and “DIAL --)” appears on display. Enter the phone
number with the number buttons. Press SEL/VOL to confirm and save your phone
number into the preset location. “SAVE OK “ appears on display for few seconds.
*How to delete a phone number in the phonebook
Select the phone number in PRE-NUM. Press and hold LOU/ BND/ key for 2 sec-
onds. “EMPTY” appears on display. The number selected is deleted from the phone-
book.
2) RECELVED: Display the last call you have received (Max. 10 numbers).
3) DIALED: Display the last dialed number (Max.10 numbers).
4) MISSED: Display the call you have missed (Max. 10 numbers).
5) PHONE BK: You can copy 20 phone numbers from mobile to the phonebook 2 of the
unit via Bluetooth transmission. Follow the procedures below:
In mobile phone, enter phonebook Select number Send contact Via Blue-
tooth Select Bluetooth device Send.
MAINTENANCE
Precaution
- Clean the front panel with a soft cloth, or damp chamois leather. Never use solvents.
- Handling the Detachable Front Panel:
- Do not expose to rain or water;
- Do not drop or apply shock.
- Make sure that you keep your set away from high temperatures.
- The use of apparatus in moderate climates.
- Do not be exposed to dripping or splashing, and that no object lled with liquids, such
as vases, shall be placed on the apparatus.
- No naked ame sources such as lighted candles should be placed on the apparatus.
Cleaning the Connector
If the connector between the main unit and the front panel is dirty, it may result in ab-
normal working condition. To avoid such problems, please detach the front panel, and
clean the connector with an alcohol swab. Gently clean and avoid damaging the con-
nector.
Notes:
For the sake of safety, always shut down the engine and take out the ignition key be-
fore cleaning. Never keep your nger or any metal device on the connector directly.
Replacing the Fuse
Make sure the amperage matches the specied value when replacing the fuses. If the
fuse is blown, check the power connection and replace with a new one. If the same
problem occurs, it would be subjected to the malfunction in-house. In such cases,
please consult the nearest service dealer.
SPECIFICATIONS
General
Power Requirement
Load Impedance
Max. Power Output
Tone Controls
Dimensions
Weight Approx.
FM Tuner Section
Tuning Range
IF Range
Usable Sensitivity (-30dB)
Signal-to-noise Ratio
Stereo Separation
Frequency Response
MW Tuner Section
Frequency Range
IF Range
Usable Sensitivity (-20dB)
12V DC (11-16 V allowable)
4 ohms
40W x4
±10 dB
Bass at 100 Hz
Treble at 10 kHz
Approx. 188 x 136 x 58.5 mm (d / w / h)
Approx. 0.7 kg
87.5-108(MHz)
10.7MHz
12dBuV
50dB
30dB (1 kHz)
40-12000Hz
522-1620(kHz)
450 kHz
35dBuV
Note:
Due to continuous product improvement, specifications and design are subject to
change without prior notice.
Press AS/PS/SCH button twice. The display will show blinking “*”. Enter the characters
by pressing the corresponding buttons. Conrm entry of each character by pressing
SEL/VOL, then press LOU/BND button to start searching.
* The display will show the le name when it is found. Press SEL/VOL to start playback.
* The display will show the directory name if it is found. Press SEL/VOL to conrm. Then
rotate SEL/VOL to select your desired track, press SEL/VOL button to start playback.
- Search by folder:
1. Press AS/PS/SCH button thrice, the display will show “ROOT”.
2. Rotate the SEL/VOL knob to search your desired folder name, press SEL/VOL knob
to enter the selected folder.
3. Rotate the SEL/VOL knob to select your desired track, press SEL/VOL button to start
playback.
GB - 14
Repeat above steps to transmit up to 20 numbers.
Retrieving the phone number in phonebook 2:
Press T-MENU/TRANS repeatedly to select “PHONE BK”. Rotate SEL/VOL to select
the phone number.
To delete a number in phonebook 2:
Press T-MENU/TRANS repeatedly to select “PHONE BK”. Rotate SEL/VOL to select
the phone number. Press LOU/BND/ for 2 seconds. “DELETING” will appear on
display for few seconds. The number selected is deleted.
6) MANU ANS (manual answer):
You can set Answer mode to “MANU ANS” (manual answer) or “AUTO ANS” (Auto An-
swer).
The unit is defaulted at manual answer. To set auto answer, press T-MENU/TRANS
repeatedly to select “MANU ANS”. Rotate SEL/VOL to select the “AUTO ANS”, then
press SEL/VOL to conrm.
When there is incoming call, the phone number appears on display.
- In manual answer mode, press button to answer the call, or press button to
reject the incoming call.
-In auto answer mode, the unit will answer the call automatically.
GB - 18
REG: OFF/ON
REGION ON mode: AF switching or PI SEEK is implemented to the station which have all PI
codes are the same as current station.
REGION OFF mode: The regional code in the format of PI code is ignored when AF switch-
ing or PI SEEK is implemented.
BUTTON FUNCTION
1/
PLAY/PAUSE
/
SELECT TRACK
TROUBLE SHOOTING GUIDE
Notes:
* There are many USB devices or SD/MMC card on the market. We cannot guarantee
to support all different models. Please try another USB device or SD/MMC card if your
device is not supported.
* The unit might not support all the multimedia les stored in SD/MMC card or USB be-
cause it includes some special playback procedure which might not be compatible with
the procedure of this unit.
KEY Mode Select
SEL/VOL(press)
M1 (1/ )
M2 (2/SCN)
M3 (3/RPT)
M4 (4/SHF)
M5 (5/DIR-)
M6 (6/DIR+)
7/AF
8/TA/EQ
9/PTY
0/DSP
SEL/VOL(rotate)
BND/LOU
ENTER(confirm entry
of each character)
A,B,C,1
D,E,F,2
G,H,I,3
J,K,L,4
M,N,O,5
P,Q,R,6
S,T,U,7
V,W,X,8
Y,Z(SPACE),9
_,-,+,0
ALL the CHARACTER
above
Start searching
Notes:
-Do not leave the microphone of Bluetooth hands-free in the places with wind passing
such as air outlet of the air conditioner. This may cause a malfunction.
-Leaving the microphone exposed to high temperatures or direct sunlight can cause
distortion or discoloration which may result in a malfunction.
-This system will not operate or may operate improperly with some Bluetooth mobile
phones / audio players.
- There are many mobile phones in the market. We cannot guarantee the compatibility
of all mobile phones together with the unit.
-If you found the conversation is not clear, try to move closer to the microphone.
- Adjust the position and direction of the microphone in order to avoid echo problem.
