Handleiding Midland BT City 2013 (pagina 3 van 9) (Engels)

543239

Verklein

Vergroot

Pagina terug

1/9

Pagina verder

Switching your Midland BTCity

on and o

Switching the unit on:

› Press and hold “Control” button down for approximately 3 seconds

until the BLUE indicator lights.

Switching the unit o:

› Press and hold both “Control” and “VOL-” buttons together for ap-

proximately 3 seconds until the RED indicator ashes 3 times, thus

lessening the chances that you might turn o the unit accidentally

(especially whilst wearing heavy gloves).

Adjusting the volume

Your Midland BTCity uses AGC technology, which automatically

adjusts the listening volume in relation to background noises.

However, it is also possible to manually adjust the volume by means

of the “Volume+” and “Volume -“buttons.

Attention: volume can be adjust only when an audio connection

is active.

Operative “mode”

The BTCity can operate in two main “mode”: Intercom and Phone

The function button on the unit can have dierent functionality de-

pending on which mode the unit is at that moment.

› In “Intercom mode” the “Control” button lets you manage the

communication.

› In “Phone mode” you can manage your Bluetooth cellular phone

to place/answer a phone call or to listen to the music (in stereo

mode). Please use your phone responsibly and safely.

You can switch (toggle) from one mode to the other simply pressing

the Middle button for 3 seconds. A voice announcement will tell in

which mode you are on.

The toggle sequence is the following:

› Intercom mode (if another unit has been paired)

› Phone mode (if a phone has been paired)

Every time you turn on the unit, the default mode is Intercom (if it

was previously paired to another unit), otherwise it will be Phone (If

was paired to a phone).

If you need to know in which mode the unit currently is, just press the

“Volume + “ and “Volume –“ button together for 3 second. A voice

announcement will tell you the current mode.

Priority

The BTCity manage the dierent connection/audio sources based on

the following priority rules.

Changing of the operative mode

Every time you change mode (long press of the middle button to tog-

gle between Intercom/ Phone), the previous audio is closed and the

control goes to the new mode.

Intercom

The Intercom has always a higher priority against the music (inclu-

ding Phone/GPS in music play mode). Every time you open the inter-

com the music from a Bluetooth source is stopped. Only the audio/

Music from the “AUX wired connection” is always in background by

default.

Phone calls

The phone call has always the higher priority and will interrupt every

connection, like music, intercom. Only the AUX wired connection can

be still on if the setting “Wired connection always in background” was

enabled.

Wire microphone

Using the Velcro/adhesive strip, place the microphone inside the hel-

met in front of your mouth. This type of microphone is more suited

for Full Faced helmets. The mini connector on the microphone allows

you choose the microphone that best suits the helmet you are using.

Audio kit jack

The audio kit must then be connected to the central jack of the

Midland BTCity unit using the “L” shaped connector.

Description of the installation brackets

The Midland BTCity can be xed onto the helmet in two dierent

ways: By either using the plate with bi-adhesive strip, or the clamp.

These methods allow you to safely “x” the BTCity unit onto your

helmet and to remove it at any time in order to recharge or store it.

Plate with bi-adhesive strip

The xing plate has a bi-adhesive strip on

one of its sides. To x the plate in place,

clean the application area on the helmet

surface, remove the bi-adhesive lm and

place the xing plate on the helmet by

keeping it contact with the surface for a

few seconds.

Clamp

Using the Allen Key, loosen the two screws on the clamp and place the

rear plate between the helmet padding and the external rigid protec-

tion. Then, tighten the two screws in order to rmly x the clamp in

place. Inside the clamp is included a small plastic spacer, that can be

removed to close tigher the clamp.

Fitting and removing your Midland BTCity

The BTCity can be easily tted onto the helmet by sliding it

downwards so that it ts into the slot of the selected xing device

(plate with bi-adhesive strip or clamp). BTCity is maintained in posi-

tion thanks to the xing clip located on the upper section (A).

To detach the BTCity, simply press the xing clip and push the unit

upwards.

Spacer

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Midland BT City 2013 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Midland BT City 2013

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info