665602
14
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
ENGLISHen
14
and then turn fully in the direction
"AUF, RELEASE". The dust collected falls from
the keyless chuck.
7.9 Threadcutting Fig. G
Only use machine tappers, which fulfil the
following conditions:
- Only use undamaged and sharp machine taps.
- Only use machine taps for right-hand threads.
Preparations:
-Make a hole (with a diameter that fits the tap
used).
- Set the gear switch (4) to Gear "1".
- Move the sliding switch (3) to "Thread
tapping"
- Adjust setting wheel (12) (see fig. below):
The appropriate setting depends on many factors,
in principle the following applies:
a) Blind holes and small through holes:
For blind holes, do not select too much torque so
that the tap does not snap when it reaches the
bottom of the hole. The Pulse position corre-
sponds to the smallest torque and the smallest
speed. Both values increase up to position 4.
b) Through holes:
Select a larger torque. From position 4 the speed
remains the same and only the torque increases.
For "Maximum torque" select position .
-Open the chuck.
-Insert tap.
- Insert taps of sizes M8 - M12, to the stop in the
chuck so that the square is held by the holder
inside the chuck.
- Smaller taps are held sufficiently tight by the
clamping jaws of the chuck.
-Close chuck and clamp tight.
- Lubricate hole and tap with appropriate cutting
oil.
Tappingthread
- Place tap on the hole.
- Move machine in axial direction.
- Depress the trigger switch (14) and at a low speed
and with moderate pressure, let the tap cut into the
hole. The speed can be increased during the
thread tapping.
- When the desired thread depth is reached, pull
the machine evenly from the hole while keep the
trigger switch (14) depressed. The machine
automatically changes its direction of rotation.
Note:
If the sliding switch (3) is in the "Thread
tapping" position, right and left pulse functions
are not available.
Note:
If the sliding switch (3) is in the position
"Thread tapping" position and there is no
pressure on the tap, the machine runs in left mode!
If pressure is placed on the tap, the machine
automatically changes to right mode.
7.10 Chuck with quick-change system Quick
Fig. I
To remove: Push the interlock ring forward (a),
advance and pull off the chuck (b).
To fit: push the interlock ring forward and move the
chuck as far as the limit stop on the drill spindle.
7.11 Fitting the belt hook (equipment-
specific) / bit depot (equipment-specific)
Fig. J
Fit the belt hook (7) as shown.
Fit the bit depot (6) as shown.
8.1 The machine's multifunctional
monitoring system
If the machine switches off automatically, the
machine electronics have activated automatic
protection mode. A warning signal sounds
(continuous beeping). The beeping stops after a
maximum of 30 seconds or when the trigger switch
(14) is released.
In spite of this protective function, overloading
is still possible with certain applications and
can result in damage to the machine.
Causes and remedies:
1. Battery pack almost empty Fig. A, B (The
electronics protect the battery pack against
damage through total discharge).
If one LED (10) is flashing, the battery pack is
almost flat. If necessary, press the button (9) and
check the LEDs (10) to see the charge level. If
the battery pack is almost flat, it must be
recharged.
2. Long continuous overloading of the machine will
activate the temperature cut-out.
Leave the machine or battery pack to cool.
Note:
if the battery pack feels very warm, the
pack will cool more quickly in an "AIR COOLED"
charger.
Note:
the machine will cool more quickly if you
operate it at idling speed.
1...10
12
1/min
Nm
2
1
3
456
...
89107
b
a
8. Troubleshooting
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo GB 18 LTX BL Q I bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo GB 18 LTX BL Q I in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 11,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info