672474
20
Verklein
Vergroot
Pagina terug
1/25
Pagina verder
20
Installation manual
Installing the cutting blade
4. Remove the cutting attachment guard.
See Removing and installing the cutting attachment
guard.
5. Place the cutting blade on the drive shaft (Fig. 14).
6. Centre the cutting blade on the drive shaft housing
(Fig. 14).
7. Ensure that the cutting blade is centred and is situated
flat against the drive shaft housing.
8. Align the shaft bush hole with the slot for the safety bar
and guide the safety bar into the shaft bush hole (Fig. 11).
9. Attach the cutting holder and nut to the drive shaft
(Fig. 14). Check that the blade has been installed
properly.
10. While holding the safety bar, tighten the nut anti-
clockwise (Fig. 15). – Tightening torque 37 Nm –
If you do not have a torque wrench, turn the nut against
the blade holder until it is situated firmly on the shaft
bush. Check that the blade has been installed
properly and then turn the nut anti-clockwise a further
¼ to ½ turn (Fig. 15).
11. Remove the safety bar from the safety bar slot.
12. Remove the guard from the cutting blade.
Removing the cutting blade and installing the
cutting attachment (depending on model)
Removing the cutting blade
1. Attach the guard to the cutting blade.
2. Align the shaft bush hole with the slot for the safety bar
and guide the safety bar into the shaft bush hole (Fig. 11).
3. Hold the safety bar in place by gripping it together
with the shaft of the unit (Fig. 12).
4. While holding the safety bar, loosen the nut on the blade
by turning it clockwise with a screw key or socket
wrench (Fig. 16).
5. Remove the nut, blade holder and blade.
Keep the nut and blade together in a secure location for
subsequent use. Keep them out of the reach of children.
Installing the cutting attachment
6. Align the shaft bush hole with the slot for the safety bar
and guide the safety bar into the shaft bush hole (Fig. 11).
Place the blade holder on the drive shaft with the flat
surface against the drive shaft housing (Fig. 13).
Rotate the cutting attachment anti-clockwise onto
the drive shaft. Tighten firmly.
Note: The blade holder must be installed on the drive
shaft in the illustrated position, otherwise the cutting
attachment will not function properly.
7. Remove the safety bar.
8. Install the cutting attachment guard. See Removing and
installing the cutting attachment guard.
Information on oil and fuel
Recommended oil grade
Use quality oil only, API classification TC (TSC-3)
which is offered for air-cooled two-stroke engines.
Mix the oil for two-stroke engines according
to the instructions on the container, 1:40 (2.5 %).
Recommended petrol grade
Danger: Under certain conditions petrol is extremely
flammable and explosive.
Refuel only in a well ventilated area and with the engine
switched off. Do not smoke and switch off all ignition
sources in the vicinity of the tank or at the fuel storage
depot.
Do not overfill the petrol tank (there must be no fuel
in the inlet nozzle). After filling up the petrol tank,
ensure that the tank cap is closed and secured.
When filling up the petrol tank, do not spill any fuel.
Spilled fuel or petrol vapours may ignite. If fuel has been
spilled, ensure that the area is dried before the engine
is restarted.
Prevent repeated or prolonged skin contact or inhalation
of the vapours.
Always use clean, fresh lead-free petrol (maximum
30 days old).
Minimum octane number: 91 ROZ
Fill the tank with petrol
Remove the tank cap.
Fill fuel tank. Never overfill!
Firmly close the petrol tank again.
Move the unit approx. 10 m from the filling station/fuel
container before starting the engine.
See instructions on mixing oil and petrol
Age and/or incorrectly mixed fuel are the main reasons
for the unit not running properly. Use fresh, clean, lead-free
petrol only. Follow exactly the instructions for the correct
petrol/oil mixture.
Correctly mix two-stroke engine oil and lead-free petrol,
1:40 (2.5 %). Do not mix directly in the tank.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

MTD-827-series

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MTD 827 series bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MTD 827 series in de taal/talen: Engels als bijlage per email.

De handleiding is 2,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van MTD 827 series

MTD 827 series Gebruiksaanwijzing - Nederlands - 26 pagina's

MTD 827 series Gebruiksaanwijzing - Deutsch - 27 pagina's

MTD 827 series Gebruiksaanwijzing - Français - 27 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info