733407
10
Verklein
Vergroot
Pagina terug
1/136
Pagina verder
EN
10
XY WARNING: Inadequate extension cords
can be dangerous.
XJ WARNING: If an extension cord is used,
the plug and socket must be of watertight
construction.
Information for supply may also be obtained
from the plug manufacturer.
<16 A <25 A
<20 m ø 1,5 mm
2
14 AWG
ø 2,5 mm
2
12 AWG
20 m - 50 m ø 2,5 mm
2
12 AWG
ø 4,0 mm
2
10 AWG
> PLUG
HOW TO CONNECT THE CORD TO A U.K. PLUG:
IMPORTANT The wires in the mains lead are
coloured in accordance with the following
code:
Blue Neutral
Brown Live
Yellow/Green Earth
Please read the in-
structions given
below before con-
necting the cord to
a plug. If in doubt
please consult a
qualified electri-
cian. As the colours
of the wires in the
mains lead of this
appliance may not
correspond with
the coloured mark-
ings identifying the
terminals in your plug, proceed as follows:
The wires that is coloured Brown must be con-
nected to the terminal which is marked with
the letter L or coloured Red. The wire that is
coloured Blue must be connected to the ter-
minal which is marked with the letter N or col-
oured Black.
Safety points for rewireable or moulded plug:
The mains lead of this appliance may be already
fitted with a BS1363 13A plug.
- If your socket outlet is not suitable for the
plug, then the plug must be removed (cut
off if it is a moulded on plug), the flexible
cord insulation should be stripped back as
appropriate and a suitable 3 pin plug fitted.
WARNING: Dispose of a plug that has been
cut from the power supply cord, as such
a plug is hazardous if inserted in a live 13A
socket outlet elsewhere in the house.
- Should the fuse need to be replaced an ASTA
marked fuse, approved to BS1362, of the
same rating must be used.
- Always replace the fuse cover after fitting
a fuse. The plug must NOT be used if the
cover is omitted or lost until a replacement
is obtained.
- Make certain that only the correct fuse cover
is used and fitted.
- For plugs with detachable fuse cover the
replacement must be the same as the colour
insert in the base of the plug, or as directed
by the embossed wording on the base of the
plug.
- If the detachable fuse cover is lost a
replacement may be purchased from a
Service Centre.
( if fitted)
NOTE: (Automatic Stop System),
which stops the machine during the
bypass phase. To start the water cleaner, it
is therefore necessary to set the switch on
position (I)“ON”; after that press the pistol
trigger: the Automatic Stop System will start
the machine and will stop it automatically
when the trigger is released. It is advisable
to put on the safety of the pistol trigger
whenever the machine is stopped, in order
to avoid unintentional starting.
· Any automatic start of the machine without
pressing the gun trigger is attributable to
air bubbles in the water or other similar
phenomena which do not imply the
existence of any defects in the machine.
· Do not leave the appliance unattended
during the standby for more than 5 minutes.
Contrarily, for the safety of the appliance it
is necessary to re-turn the switch into the (0)
OFF position.
· Please check that the coupling of the high
pressure hose with the appliance and the
gun supplied as standard equipment made
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lavorwash STM 160 Kit 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lavorwash STM 160 Kit 2 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info