Handleiding Kratki Arke (pagina 14 van 136) (Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Zweeds)

813979

Verklein

Vergroot

Pagina terug

1/136

Pagina verder

Preparation for installation

The replace insert is delivered ready to be built and installed. After unpacking, check the complete-

ness of the unit and make sure that the kit components have not been damaged during transport. In

selected replace inserts, the deector, handle, air damper handle and the rod handle used to adjust

the ue gas damper (shaft) should be installed.

In guillotine-type inserts, the screws locking the counterweight should additionally be removed. De-

pending on the model, check:

- the mechanism for adjusting the chimney draught (shaft),

- the mechanism for adjusting the air supply to the combustion chamber (ash drawer, air damper),

- the mechanism of operation of the front door closure (guides, hinges, handle),

- correctness of installation of ash pan/ash drawer and grate,

- the condition of the glass and the sealing cord of the re door,

- the condition of the ceramic lining of the rebox (selected replace inserts).

The inspection should be carried out in the presence of the installer. If you nd any damage or decien-

cies, please contact customer service. Before installing the replace insert, the chimney ue must be

expertly inspected and received for its technical parameters and condition - tightness, patency. Instal-

lation of the replace stove can be carried out after a positive result of the chimney sweep’s expertise

of the ue, and after checking the completeness of the device and the proper operation of all the

mechanisms mentioned above.

Location of the replace insert and connection to the chimney

The replace insert must be installed on a noncombustible oor with a minimum thickness of 30 cm,

and the oor at the replace door must be protected by a strip of noncombustible material with a

minimum width of 50 cm. The safe distance of combustible elements from the glass should be min.

150 cm (Fig. 1 b). Before installing the replace, it is also necessary to check the mechanical strength

of the oor on which the replace insert is to be placed, taking into account the total weight of the

insert and its housing.

The device should be located as close as possible to the ue pipe. When moving the replace, do not

grab the handle, as you risk damaging it. The appliance must be placed at a safe distance from any

ammable products. The ue under which the replace is connected should be airtight, smooth and

made of low heat-conducting materials. The connection between the chimney and the replace stove

must be made of non-ammable materials protected against oxidation (enamel or steel ue pipe).

Connection to a common chimney is possible.

When connecting to a common chimney, the door must always be closed. The pressure of the chimney

should be 12 Pa.

A diagram of an example installation and connection to the chimney is shown in Figure 1 a) ( 1 - -

replace insert, 2 - interior of the housing, 3 - decompression chamber , 4 - outdoor air intake duct,

5 - outdoor air intake, 6 - chimney, 7 - connector, 8 - ventilation grille, outlet, 9 - ventilation grille, inlet,

10 - layer of non-combustible material).

The appliance should be connected under a chimney section that provides a draught of 12 +- 2 Pa. If

the chimney produces a weak draught, consider laying new ues. It is also important that the chim-

ney does not produce excessive draught, in which case a draught stabilizer should be installed in the

chimney. Alternatively, special chimney endings equipped with an exhaust fan that regulates draught,

or other chimney attachments (e.g. a reman) may be used. Have your chimney ue inspected by a

master chimney sweep.

The room in which the device will be installed must have a volume resulting from the ratio of 4 m 3 x

1 kW of nominal thermal power of the device, but not less than 30 m3. In addition, it should have an

ecient ventilation system and provide the necessary amount of air required for the proper operation

of the cartridge. It is assumed that to burn 1 kg of wood in a replace with a closed combustion cham-

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Kratki Arke Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info