683161
52
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Transmission
Audio Transmission
1 Press and hold the [PTT] key on the microphone or
press the [SEND] key.
The transmitting status is activated and the [BUSY/TX] LED
lights up in red.
2 Speak into the microphone in the normal tone and
loudness.
3 Release the [PTT] key on the microphone or press the
[SEND] key.
Doing so restores the receiving status.
CW Transmission
Performing the following steps when a key or paddle is connected
enables transmission in the CW mode.
1 Press [CW/ CW-R] to select CW mode.
2 Press [VOX] to enable break-in.
3 Operate the keyer or paddle.
Adjusting Microphone Gain
Microphone gain can be adjusted in the SSB or AM mode as
follows while referring to the ALC meter display.
1 Press and hold the [PTT] key on the microphone or
press the [SEND] key.
The transmitting status is activated and the [BUSY/TX] LED
lights up in red.
2 Speak into the microphone in the normal tone and
loudness.
3 Turn the [MIC/PITCH] control to adjust the microphone
gain level.
Microphone gain is displayed as MIC:nnn at the top of the
screen. [nnn: 0 to 100]
.
When in the SSB mode
Turn the [MIC/PITCH] control while speaking into the
microphone. The ALC meter fluctuates according to the
volume level. Ensure that the maximum level does not exceed
the ALC zone during the adjustment.
When in the AM mode
Turn the [MIC/PITCH] control while speaking into the
microphone. Adjust in such a way that the PWR meter
fluctuates slightly according to the volume level.
4 Release the [PTT] key on the microphone or press the
[SEND] key.
Depending on the squelch level setting, the [BUSY/TX] LED
may light up in green or go off.
Speak into the microphone in the normal tone and
loudness. Make sure that your mouth is not too close to
the microphone and do not speak too loudly. Doing so
may increase the extent of distortion, thus causing
audibility to deteriorate at the receiving end.
To use a speech processor, refer to “Speech
Processor” (8-4).
Note that the output level tend to be larger when a
microphone with a built-in AF amplifier is used.
Microphone gain in the FM mode can be configured in
Advanced Menu [10] Microphone Gain (FM Mode).
Adjusting TX Output Power
Maintain a TX output power level that is as low as possible while
ensuring that communication can be carried out smoothly. Doing
so reduces the likelihood of interference with other stations.
The TX output power level can also be adjusted while transmission
is in progress.
Turn the [POWER] control to adjust the TX output
power.
Turning the [POWER] control to the right increases the output
level, while turning it to the left reduces the output level. The
selectable range varies with the band and mode in use as
follows.
Other than AM AM
HF Band 5 to 100 [W] 5 to 25 [W]
50 MHz Band 5 to 100 [W] 5 to 25 [W]
70 MHz Band (E type) 5 to 50 [W] 5 to 12.5 [W]
Output is displayed in a step size of 1 W. An output of
12.5 W will be shown as “12 W”.
Fine Adjustment of TX Output Power
It is possible to alter the step size when the [POWER] control is
turned.
Configure in Menu [6-04]
Transmit Power Step
Size
Setting Value 1 [W]/ 5 (default) [W]
1[W]: Adjusts the TX output level in a step size of 1 W.
5[W]: Adjusts the TX output level in a step size of 5 W (e.g., 5,
10, 15...).
4 BASIC OPERATIONS
4-8
52

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info