511243
12
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
4
1 INSTALLATION
ANTENNA CONNECTION
An antenna system consists of an antenna, feed line, and ground. The transceiver can give excellent results if the
antenna system and its installation are given careful attention. Use a properly adjusted 50 antenna of good
quality, a high-quality 50 coaxial cable, and first-quality connectors. All connections must be clean and tight.
After making the connections, match the impedance of the coaxial cable and antenna so that the SWR is 1.5:1 or
less. High SWR will cause the transmit output to drop and may lead to radio frequency interference to consumer
products such as stereo receivers and televisions. You may even interfere with your own transceiver. Reports
that your signal is distorted could indicate that your antenna system is not efficiently radiating the transceiver’s
power.
Connect your primary HF/ 50 MHz antenna feed line to ANT 1 on the rear of the transceiver. If you are using two
HF/ 50 MHz antennas, connect the secondary antenna to ANT 2. Refer to page 16 for the location of the antenna
connectors.
Note:
Transmitting without connecting an antenna or other matched load may damage the transceiver. Always connect the antenna to the
transceiver before transmitting.
All fixed stations should be equipped with a lightning arrester to reduce the risk of fire, electric shock, and transceiver damage.
The transceivers protection circuit will activate when the SWR is greater than 2.5:1; however, do not rely on protection to compensate for a
poorly functioning antenna system.
GROUND CONNECTION
At the minimum, a good DC ground is required to prevent such dangers as electric shock. For superior
communications results, a good RF ground is required against which the antenna system can operate. Both of
these conditions can be met by providing a good earth ground for your station. Bury one or more ground rods or
a large copper plate under the ground, then connect this to the transceiver GND terminal. Use heavy gauge wire
or a copper strap, cut as short as possible, for this connection. Do not use a gas pipe, an electrical conduit, or a
plastic water pipe as a ground.
LIGHTNING PROTECTION
Even in areas where lightning storms are less common, there are usually a limited number of storms each year.
Consider carefully how to protect your equipment and home from lightning. The installation of a lightning arrestor
is a start, but there is more that you can do. For example, terminate your antenna system transmission lines at an
entry panel that you install outside your home. Ground this entry panel to a good outside ground, then connect
the appropriate feed lines between the entry panel and your transceiver. When a lightning storm occurs,
disconnecting the feed lines from your transceiver will ensure additional protection.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-480SAT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-480SAT in de taal/talen: Engels als bijlage per email.

De handleiding is 6,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-480SAT

Kenwood TS-480SAT Gebruiksaanwijzing - Nederlands - 104 pagina's

Kenwood TS-480SAT Gebruiksaanwijzing - Deutsch - 104 pagina's

Kenwood TS-480SAT Gebruiksaanwijzing - Français - 104 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info