Handleiding Jablotron JA-80Y - GSM communicator (pagina 2 van 12) (Engels)

631261

Verklein

Vergroot

Pagina terug

1/12

Pagina verder

The JA-80Y GSM communicator - 2 - MFJ55304

a) dial the system’s SIM card number (if a phone is connected to the

communicator’s simulated line it will start ringing)

b) after 25 seconds of ringing (programmable) the system will answer with

a short beep

c) key in a valid access code on the telephone keypad (e.g. 8080 or 1234

if factory default settings are still valid)

d) the phone keypad will behave as a system keypad and an acoustic

signal in the receiver will indicate the control panel status: 1 beep =

SET, 2 beeps = UNSET, 3 beeps = Service mode, 4 beeps = incorrect

code entry, siren sound = alarm

e) now the system can be operated from the phone keypad the same way

as from the system keypad – including the commands starting with ∗ (for

example ∗81 to turn the PGX output on)

f) to exit this mode simply end the phone call (if nothing is entered within

a minute, the phone call will end automatically anyway)

Notes:

 do not enter sequences on the phone too fast, each key signal

needs a certain time to be sent (it depends on the particular phone and

the quality of the GSM connection)

 a fixed-line phone can also be used to operate the system remotely

the same way (the phone must use tone dialling)

 the system can also be operated from the keypad of a phone

connected directly to the communicator’s simulated line. It is only

necessary to pick up its receiver and briefly press the # key. Then the

phone is ready to work as a control panel keypad. To finish operating

just hang up.

 Phone keypads have to be re-authorized each time the system is

called by entering the codes specified earlier, as phone keypads are

only authorized as system keypads for the duration of a call to the

system.

3.4. SMS instructions to control the system remotely

All incoming SMSes are checked by the communicator and if there are

any instructions to the system, they will be performed. Each instruction

message must have the following format:

code instruction

(valid code space instruction)

Valid code = any valid code in the system (e.g. 8080, 1234 etc.)

The factory-default instruction texts (editable – see 5.5)

Instruction Function Note

SET setting (arming)

UNSET unsetting

(disarming)

setting or unsetting (the same way as

if the used code is entered on the

system keypad), If the system is

already in the desired mode, it will not

change

STATUS status

interrogation

including GSM signal strength, GPRS

data, ARC communication (shown as

MS1 and MS2)

MEMORY last event

interrogation

The last event recorded in the control

panel memory

PGX ON turns on PGX

PGX OFF turns off PGX

PGY ON turns on PGY

PGY OFF turns off PGY

the PG output has to be programmed

for the function: on/off (by 237/247) or

2 second switching (by 238/248)

AUX ON turns on AUX

AUX OFF turns off AUX

turns a pair of AUX terminals on the

communicator module on/off

CREDIT

SIM card credit

interrogation

it has to be initialised by SMS before it

can function – see 5.17

Example: by sending: “code SET” (valid code space SET) the system

will set (if it is already set it will not change its status)

Notes:

 performance of the instruction is confirmed by an SMS reply

 the instruction texts are not case-sensitive and only ASCII characters

are allowed

 only one instruction can be in an instruction SMS

 a setting/unsetting instruction starting with the service code will only be

performed if setting/unsetting with the service code is enabled in the

control panel (to protect against unauthorized setting/unsetting by

installers)

 an SMS instruction can also be sent to the alarm system from a phone

connected to the communicator (if supports SMS) – to phone number

001 (for free)

 if there is any other text in the instruction not separated by “%”, the

instruction will not be performed

 if you are sending an instruction and you are not sure whether any

other text will be automatically added to the SMS (for example, when

using an SMS internet gate) type the instruction as: %code

instruction%%

3.5. Toll-free remote control by unanswered calls from pre-

authorized phones

A limited number of system functions can be activated remotely by

calling the system from pre-authorized phones and terminating calls

before the system answers. This way limited control of the system is free

of call charges. It is possible to pre-authorize phone numbers stored in

memories M1 to M8 (also used for event reporting – see 4).

To pre-authorize a telephone number store ∗ at the end of the number

and follow it by a single digit (1, 2, 3, 8 or 9) – see the notes in section 4.

If this number calls, the communicator generates “∗ digit“ after the first

ring (as if it had been entered manually on the system keypad). This toll-

free remote control by unanswered calls enables the following functions

according to the digit stored at the end (after the *) of the tel. number in

memory:

∗1 setting the complete system (= ABC keypad button)

∗2 setting section A (= A button)*

∗3 setting sections A & B or B (= B button)*

∗8 PGX turns on for 2 sec. (if PGX is programmed for the pulse

function)

∗9 PGY turns on for 2 sec. (if PGY is programmed for the pulse

function)

Notes:

 if a phone sends no caller identification data it cannot be used for

this type of remote control by phone

 if phone calls end before the control panel answers, remote control is

for free

 a phone which is pre-authorized for toll-free remote control can also

temporarily authorize its keypad to fully operate the system (see

3.3) – just let it ring until the control panel answers the call

 if it is desired that the phone which is authorized for toll-free remote

control should not receive event reports, then turn the reports off for

that tel. number (see 5.4).

 setting (arming) with ∗1, ∗2 and ∗3 will work only if enabled in the

control panel

4. Reporting to phones

The communicator can report events occurring in the Oasis system by

sending SMS reports and/or by calling phone numbers with an acoustic

signal (mostly used as audible notification of an SMS to be read). Reporting

can be programmed for up to 8 phone numbers.

The most frequently desired reports are already assigned to the telephone

number memories by factory-default, so you only need to program tel.

numbers to the particular memories which have the desired reports already

assigned. If desired, other events can be reported to the number too, i.e. the

list of event reports assigned to the number can be changed (see 5.4)

Factory-default reports assigned to the numbers M1 to M8

M Reports

Alarms and faults by SMS

Alarms and faults by SMS + phone call (if you answer the

call you hear a siren sound)

Alarms by SMS + a phone call, with Setting/Unsetting

and faults by SMS only

Alarms by phone call (if you answer the call you hear a

siren sound)

8 Technical fault by SMS (suitable for an installer)

To program phone numbers to the M memories, enter the following

sequence while in Service mode:

81 M xxx...x ∗0

where:

M is memory 1 to 8

xxx...x is a phone number (max. 20 digits)

Example: entering 81 5 777 777 777

∗

0 will store the number

777777777 in memory M5 (Alarms will be reported by SMSes + phone

calls, Setting/Unsetting and faults only by SMS)

To erase a number from memory M enter: 81 M ∗0

Notes:

 Entering ∗9 before the first digit will insert a “+” for the international

formatting of phone numbers

Jablotron JA-80Y - GSM communicator Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Jablotron JA-80Y - GSM communicator

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info