477548
13
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
English – 13
MAINTENANCE
Maintenance
Air filter
The air filter must be regularly cleaned to remove dust and dirt
in order to avoid:
Carburettor malfunctions
Starting problems
Loss of engine power
Unnecessary wear to engine parts.
Excessive fuel consumption.
Clean the air filter daily, or more often in demanding
conditions.
The air filter is dismantled once the air filter cover has been
lifted off. Press in the catches on the top of the air filter cover
and lower the cover.
Remove the air filter and check that it is undamaged. Replace
with a new air filter if you believe it to be defective.
Clean the filter by knocking the filter carefully against a hard
surface and blowing with compressed air from inside. Never
brush the dirt away. Replace the air filter if it is very dirty.
An air filter that has been in use for a long time cannot be
cleaned completely. The filter must therefore be replaced with
a new one at regular intervals. A damaged air filter must
always be replaced.
When reassembling, make sure that the filter completely
seals against the filter holder.
Spark plug
If the machine is low on power, difficult to start or runs poorly
at idle speed: always check the spark plug first before taking
any further action. If the spark plug is dirty, clean it and check
that the electrode gap is 0.7-0.8 mm. The spark plug should
be replaced after about a month in operation or earlier if
necessary.
CAUTION! Always use the recommended spark plug type!
Use of the wrong spark plug can damage the piston/cylinder.
Muffler
The muffler is designed to reduce the noise level and to direct
the exhaust gases away from the operator. The exhaust
gases are hot and can contain sparks, which may cause fire
if directed against dry and combustible material.
Regularly check that the muffler is securely attached to the
machine.
Never use a machine that has a faulty muffler.
Cutter
It is important to have a sharp and correctly balanced cutter.
Loosen the bolt holding the cutter and leave the cutter at a
service workshop at least once a year for grinding and
balancing. An appropriate time to do this is after the mowing
season has finished.
If the cutter or cutter bracket need to be changed you must
replace the cutter bolt, washer and friction washer at the
same time.
The bolt should be tightened with a torque of 45-60 Nm when
you fit the cutter again. See instructions under the heading
Assembly.
!
WARNING! Make sure the cutting attachment
has stopped before cleaning, carrying out
repairs or an inspection. Disconnect the HT
lead from the spark plug.
!
WARNING! The muffler gets very hot in use
and remains so for a short time afterwards.
Do not touch the muffler if it is hot!
!
WARNING! Always wear heavy-duty gloves
when repairing the cutting attachment. The
blades are very sharp and can easily cause
cuts.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Husqvarna WB533Se bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Husqvarna WB533Se in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info