13107
14
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
−−
Storage Precautions
TRANSPORTING
Removal from Storage
Engine Oil
Draining the Fuel Tank and Carburetor
ENGLISH
SEDIMENT CUP
DRAIN BOLT
FUEL VALVE LEVER
Align notch on pulley with hole at top of cover.
GASKET
O-RING
ON
14
If your engine will be stored with gasoline in the fuel tank and
carburetor, it is important to reduce the hazard of gasoline vapor
ignition. Select a well-ventilated storage area away from any
appliance that operates with a flame, such as a furnace, water
heater, or clothes dryer. Also avoid any area with a spark-
producing electric motor, or where power tools are operated.
If possible, avoid storage areas with high humidity, because that
promotes rust and corrosion.
Keep the engine level in storage. Tilting can cause fuel or oil
leakage.
With the engine and exhaust system cool, cover the engine to
keep out dust. A hot engine and exhaust system can ignite or melt
some materials. Do not use sheet plastic as a dust cover. A
nonporous cover will trap moisture around the engine, promoting
rust and corrosion.
Gasoline is highly flammable and explosive, and you
can be burned or seriously injured when handling
fuel.
Stop engine and keep heat, sparks, and flame away.
Wipe up spills immediately.
Place an approved gasoline container below the carburetor, and
use a funnel to avoid spilling fuel.
If the cylinder was coated with oil during storage preparation, the
engine will smoke briefly at startup. This is normal.
If the fuel was drained during storage preparation, fill the tank with
fresh gasoline. If you keep a container of gasoline for refueling, be
sure it contains only fresh gasoline. Gasoline oxidizes and
deteriorates over time, causing hard starting.
Check your engine as described in the
BEFORE OPERATION
CHECKS
section of this manual (see page ).
If equipped with a battery for electric starter types, recharge the
battery once a month while the engine is in storage.
This will help to extend the service life of the battery.
Handle fuel only outdoors.
Remove the carburetor drain bolt and gasket. Remove the
sediment cup and O-ring, then move the fuel valve lever to the
ON position.
After all the fuel has drained into the container, reinstall the
drain bolt, gasket, sediment cup and O-ring. Tighten the drain
bolt and sediment cup securely.
Change the engine oil (see page ).
Pour a tablespoon 5 10 cm
(5 10 cc) of clean engine oil into
the cylinder.
Pull the starter rope several times to distribute the oil in the
cylinder.
Reinstall the spark plug.
Pull the starter rope slowly until resistance is felt and the notch
on the starter pulley aligns with the hole at the top of the recoil
starter cover. This will close the valves so moisture cannot enter
the engine cylinder. Return the starter rope gently.
Remove the spark plug (see page ). Keep the engine level when transporting to reduce the possibility
of fuel leakage. Turn the fuel valve to the OFF position (see
page ).
2.
1.
3.
1.
2.
3.
4.
5.
6.
3
9
12
5
05/06/17 17:26:47 32Z4F601_014
14

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Honda-Honda-Engines-GX200

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Honda Honda Engines GX200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Honda Honda Engines GX200 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Honda Honda Engines GX200

Honda Honda Engines GX200 Gebruiksaanwijzing - Nederlands - 60 pagina's

Honda Honda Engines GX200 Gebruiksaanwijzing - Nederlands - 33 pagina's

Honda Honda Engines GX200 Gebruiksaanwijzing - Deutsch, Italiano - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info